Sharp PG-F320W specifications Setup Menu Main Menu, Advanced Setup Menu

Page 22

Setting up the Projector Using RS-232C or Telnet

SETUP MENU (Main Menu)

▼SETUP MENU

---------------------------------

SETUP MENU--------------------------------

 

[1]IP Address

[2]Subnet Mask

[3]Default Gateway

[4]User Name

[5]Password

 

[6]RS-232C Baud Rate

[7]Projector Name

[8]DHCP Client

[A]Advanced Setup

 

[D]Disconnect All

[V]View All Setting

[S]Save & Quit

[Q]Quit Unchanged

setup>

 

 

 

 

 

[1]IP Address

IP address settings. (Page 25)

[2]Subnet Mask

Subnet mask settings. (Page 25)

[3]Default Gateway

Default gateway settings. (Page 25)

[4]User Name (Factory default setting : Not Re- quired)

Setting of user name for security protection. (Page 25)

[5]Password (Factory default setting : Not Required)

Setting of password for security protection. (Page 26)

[6]RS-232C Baud Rate (Factory default setting : 9600 bps)

Baud rate settings for the RS-232C terminals. (Page

26)

[7]Projector Name

It is possible to assign a projector name. (Page 26)

[8]DHCP Client

DHCP Client settings. (Page 26)

[A]Advanced Setup

Enters ADVANCED SETUP MENU. (Page 27)

[D]Disconnect All

Disconnect all connections. (Page 27)

[V]View All Setting

Displays all setting values. (Page 23)

Can also be used with ADVANCED SETUP MENU.

[S]Save & Quit

Save set values and quit menu. (Page 24)

[Q]Quit Unchanged

Quit menu without saving setting values. (Page 24)

ADVANCED SETUP MENU

▼ADVANCED SETUP MENU

******************** ADVANCED SETUP MENU ***********************

[1]Auto Logout Time

[2]Data Port

[5]Network Ping Test

 

[6]Accept IP Addr(1)

[7]Accept IP Addr(2) [8]Accept IP Addr(3)

[9]Accept All IP Addr

[0]Search Port

[!]Restore Default Setting [Q]Return to Main Menu

advanced>

[1]Auto LogoutTime (Factory default setting : 5 min- utes)

Setting of time until automatic disconnection of net- work connection. (Page 27)

[2]Data Port (Factory default setting : 10002)

Setting the TCP port number used when exchang- ing data. (Page 27)

[5]Network Ping Test

It is possible to confirm that a network connection between the projector and a computer etc. is work- ing normally. (Page 28)

[6]Accept IP Addr(1) [7]Accept IP Addr(2) [8]Accept IP Addr(3)

[9]Accept All IP Addr (Factory default setting : Ac- cept All)

For improved security, it is possible to set up to three IP addresses allowing connection to the projector. Set IP addresses can be cancelled using [9] Accept All IP Addr. (Page 28)

[0]Search Port (Factory default setting : 5006) Setting the port number used when searching for the projector. (Page 29)

[!]Restore Default Setting

Restores all setting values that can be set using the menu to the default state. (Page 29)

[Q]Return to Main Menu

Return to the main SETUP MENU. (Page 29)

Note

•When “DHCP Client” is set to “OFF” on the projector:

IP address : 192.168.150.2

Subnet mask : 255.255.255.0

Default gateway : 0.0.0.0

-22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Setup Manual Connecting Pin Assignments Sub 15 pin female connectorConnecting Pin Assignments Computer control Communication conditions RS-232C Specifications and CommandsBasic format Commands ← O KControl Contents BrilliantColorTM OK or ERR PAL Setting up the Projector Network Environment Network settings on the computerConnecting the Pro- jector to a Computer Setting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector DNS Controlling the Projector via LAN Controlling the Projector Using Internet ExplorerVersion 5.0 or later Status Status Confirming the ProjectorControlling the Projector ControlProjector Settings & Adjustments Setting and AdjustingSetting the Security Network SecurityMail Originator Settings Making General Settings for the Network NetworkSetting for Sending E-mail when an Error Occurs GeneralMail Recipient Settings Occurs Service & Support Access URLSetting up the Projector Using RS-232C or Telnet When Connecting Using RS-232CWhen Connecting Using Telnet ClickStartfrom theWindows desk- top and select RunSetup Menu Main Menu Advanced Setup MenuVView All Setting View Setting Detail ListSet Items SSave & Quit Save Settings and QuitQuit without Saving Set Tings QQuit UnchangedSubnet Mask Setting IP Address SettingDefault Gateway Setting User Name SettingDhcp Client Setting Password SettingProjector Name Setting RS-232C Baud Rate SetEntering Advanced Setup Menu Disconnecting All ConnecSetting Auto Logout Time Data Port SettingCarrying out Network Ping Test Setting of Accept IP Ad- dressAccepting All IP Addresses Return to Default Settings Setting of Search PortReturn to Main Menu Resetting the Lamp Timer of the Projector via LAN Resetting the Lamp Timer of the Projector via LAN Troubleshooting Communication cannot be established with the projectorTroubleshooting \ After the initialization, carry out setting again
Top Page Image Contents