Sharp PG-F320W Disconnecting All Connec, Setting Auto Logout Time, Entering Advanced Setup Menu

Page 27

Setting up the Projector Using RS-232C or Telnet

Disconnecting All Connec-

tions ([D]Disconnect All)

Setting Auto Logout Time

(ADVANCED[1]Auto Logout Time)

It is possible to disconnect all the TCP/IP connec- tions currently recognized by the projector. Even if the COM Redirect port is fixed in the Busy status due to a problem, it is possible to force the Ready status back by carrying out this disconnection.

setup>d

1

Disconnect All Connections(y/n)?y

2

Now Disconnecting...

 

 

 

1Enter “d” and press the “Enter” key.

2 Enter “y” and press the “Enter” key.

Note

•If Disconnect All is performed, the connection to the projector via network will be forcibly discon- nected.

Entering ADVANCED SETUP MENU

([A]Advanced Setup)

Enters ADVANCED SETUP MENU.

setup>a

1

******************** ADVANCED SETUP MENU ***********************

[1]Auto Logout Time

[2]Data Port

[5]Network Ping Test

 

[6]Accept IP Addr(1)

[7]Accept IP Addr(2) [8]Accept IP Addr(3)

[9]Accept All IP Addr

[0]Search Port

[!]Restore Default Setting [Q]Return to Main Menu

advanced>

1 Enter “a” and press the “Enter” key.

If there is no input after a fixed time, the projector automatically disconnects network connection using the Auto Logout function. It is possible to set the time until the projector is automatically disconnected in units of a minute (from 1 to 65535 minutes).

advanced>1

 

 

1

Valid range

: 0 to 65535 (minute)

 

 

note: if you enter “0”, auto logout function will be disable.

 

 

Auto Logout Time : 5

 

 

Please Enter

:15

 

 

2

 

 

(change)

—> 15

*

1Enter “1” and press the “Enter” key.

2Enter numerical value and press the“Enter”key. Display set numerical value (*).

Note

•If the set value is made 0, the Auto Logout func- tion is disabled.

•If an invalid number is entered, an error message (“Parameter Error!”) will be displayed and the screen returns to the ADVANCED SETUP MENU.

Data Port Setting

(ADVANCED[2]Data Port)

Setting of TCP port number. It is possible to set in the range of 1025 to 65535.

advanced>2

 

 

1

Valid range

:1025 to 65535

 

 

Data Port

:10002

 

 

 

Please Enter

:10005

 

 

2

 

 

(change)

—> 10005

*

1Enter “2” and press the “Enter” key.

2Enter numerical value and press the“Enter”key. Display set numerical value (*).

Note

•Set according to need. Normally, use with the fac- tory default setting.

-27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Setup Manual Sub 15 pin female connector Connecting Pin AssignmentsConnecting Pin Assignments RS-232C Specifications and Commands Computer control Communication conditionsBasic format ← O K CommandsControl Contents BrilliantColorTM OK or ERR PAL Network settings on the computer Setting up the Projector Network EnvironmentConnecting the Pro- jector to a Computer Setting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector DNS Controlling the Projector Using Internet Explorer Controlling the Projector via LANVersion 5.0 or later Control Confirming the ProjectorControlling the Projector Status StatusNetwork Security Setting and AdjustingSetting the Security Projector Settings & AdjustmentsGeneral Making General Settings for the Network NetworkSetting for Sending E-mail when an Error Occurs Mail Originator SettingsOccurs Service & Support Access URL Mail Recipient SettingsWhen Connecting Using RS-232C Setting up the Projector Using RS-232C or TelnetClickStartfrom theWindows desk- top and select Run When Connecting Using TelnetAdvanced Setup Menu Setup Menu Main MenuView Setting Detail List VView All SettingSet Items Tings QQuit Unchanged Save Settings and QuitQuit without Saving Set SSave & QuitUser Name Setting IP Address SettingDefault Gateway Setting Subnet Mask SettingRS-232C Baud Rate Set Password SettingProjector Name Setting Dhcp Client SettingData Port Setting Disconnecting All ConnecSetting Auto Logout Time Entering Advanced Setup MenuSetting of Accept IP Ad- dress Carrying out Network Ping TestAccepting All IP Addresses Setting of Search Port Return to Default SettingsReturn to Main Menu Resetting the Lamp Timer of the Projector via LAN Resetting the Lamp Timer of the Projector via LAN Communication cannot be established with the projector TroubleshootingTroubleshooting \ After the initialization, carry out setting again
Top Page Image Contents