Sony MDS-JE640 specifications Operating the Continuous Playback Mode, Menu/No

Page 17

4-5-1. Operating the Continuous Playback Mode

1.Entering the continuous playback mode

1Set the disc in the unit. (Whichever recordable discs or discs for playback only are available.) 2Rotate the AMS knob and display “CPLAY1 MODE”(C34).

3Press the YES button to change the display to “CPLAY1 MID”.

4When access completes, the display changes to “C = AD = ”. Note : The numbers “ ” displayed show you error rates and ADER.

2.Changing the parts to be played back

1Press the YES button during continuous playback to change the display as below.

“CPLAY1 MID” t “CPLAY1 OUT” t “CPLAY1 IN”

When pressed another time, the parts to be played back can be moved.

2When access completes, the display changes to “C = AD = ”. Note : The numbers “ ” displayed show you error rates and ADER.

3.Ending the continuous playback mode

1Press the MENU/NO button. The display will change to “CPLAY1 MODE”(C34).

2Press the AEJECT button to remove the disc.

Note : The playback start addresses for IN, MID, and OUT are as follows.

IN

40h cluster

MID

300h cluster

OUT

700h cluster

4-5-2. Operating the Continuous Recording Mode (Use only when performing self-recording/palyback check.)

1.Entering the continuous recording mode 1Set a recordable disc in the unit.

2Rotate the AMS knob and display “CREC1 MODE” (C35).

3Press the YES button to change the display to “CREC1 MID”.

4When access completes, the display changes to “CREC1 ( )” and REC lights up. Note : The numbers “ ” displayed shows you the recording position addresses.

2.Changing the parts to be recorded

1When the YES button is pressed during continuous recording, the display changes as below. “CREC1 MID” t “CREC1 OUT” t “CREC1 IN”

When pressed another time, the parts to be recorded can be changed. REC goes off.

2When access completes, the display changes to “CREC1 ( )” and REC lights up. Note : The numbers “ ” displayed shows you the recording position addresses.

3.Ending the continuous recording mode

1Press the MENU/NO button. The display changes to “CREC1 MODE” (C35 ) and REC goes off.

2Press the A button to remove the disc.

Note 1 : The recording start addresses for IN, MID, and OUT are as follows.

 

IN

40h cluster

 

MID

300h cluster

 

OUT

700h cluster

Note 2

: The

MENU/NO

button can be used to stop recording anytime.

Note 3

: Do not perform continuous recording for long periods of time above 5 minutes.

Note 4

: During continuous recording, be careful not to apply vibration.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Inputs SpecificationsOutputs NEWSELF-DIAGNOSIS Function Supplied accessoriesGeneral Three- or five Digit code Cause/Remedy MessageItems of Error History Mode Items and Contents Disassembly Table of ContentsDiagrams Exploded ViewsFlexible Circuit Board Repairing Section Service NotesIOP JIG for Checking BD Board WaveformRecord Precedure Main Board Component Side Checks Prior to Parts Replacement and AdjustmentsForced Reset Bit Binary Retry Cause Display ModeHexadecimal t Binary Conversion Table Section General Front Panel Section Section DisassemblyPT BOARD, VOL-SEL Board Main BoardBD Board Mechanism Deck Section MDM-7APrecautions for USE of Test Mode Section Test ModeSetting the Test Mode Exiting the Test ModeDisplay Details Mark Group Selecting the Test ModeMENU/NO Operating the Continuous Playback ModeMode display Test Mode DisplaysError rate display Functions of Other ButtonsMeanings of Other Displays When Memory NG is DisplayedAutomatic SELF-DIAGNOSIS Function InformationCheck before replacement Section Electrical AdjustmentsParts Replacement and Adjustment YES Adjustment flowPrecautions for Adjustments Precautions for Checking Laser Diode EmissionPrecautions for USE of Optical PICK- UP KMS-260B Checks Prior to Repairs Using the Continuously Recorded DiscOther Checks Auto CheckCD Error Rate Check Play Check MO Error Rate CheckLaser Power Adjustment Initial Setting of Adjustment ValueTemperature Compensation Offset Adjutment Iop NV Save Traverse AdjustmentYES Focus Bias AdjustmentAuto Gain Control Output Level Adjustment Error Rate CheckCD Auto Gain Control Output Level Adjustment MO Auto Gain Control Output Level AdjustmentAdjusting Points and Connecting Points For schematic diagrams Section DiagramsFor printed wiring boards Circuit Boards LocationMDS-JE640 Block Diagrams BD SectionSignal Path REC Analog Main SectionDisplay Board BD BoardMain Board Semiconductor Printed Wiring Board BD SectionPIN PIN Function Printed Wiring Board Main Section Side a IC2 Printed Wiring Board Main Section Side BIC1 PIN MDS-JE640 Schematic Diagram Main /3 See page 47 for IC Block Diagrams Printed Wiring Board Power Section Printed Wiring Board Display Section Schematic Diagram Display Section See page 34 for Waveforms IC101 CXA2523AR BD Board IC Block DiagramsIC400 LA5643 Main Board IC101 CXA2523AR RF Amplifier BD Board IC PIN FunctionsMNT0 FOK Mvci Tfdr IC1 M30805SGP System Control Main Board HLDA/ALE Chassis Section Section Exploded ViewsPanel ASSY, Front Silver Panel ASSY, Front Black AEP,UK,CIS,SP,MY202 220 201 213 215 216 205 218 207 Mechanism MDM-7AMotor ASSY, Spindle HEAD, Over LightMotor ASSY, Sled Motor ASSY, LoadingSection Electrical Parts List Metal Chip IC TC7WU04FUTE12RIC MC74ACT08DTR2 IC BA033FP-E2Display KEY-SW Main CONNECTOR, FFC 17P PIN, Connector 3PPIN, Connector 4P PLUG, Connector 10P DiodeAEP,UK,CIS IC SN74LVU04ANSRTransistor UN2211-TX Transistor UN2111-TXTRANSFORMER, Power CND ConnectorTRANSFORMER, Power SP,MY Composition Circuit BlockVOL-SEL Sony Corporation
Top Page Image Contents