| SpectraLink Corporation | Setup and |
| ||
|
|
| Mitel Networks 3300 and |
| |
|
|
|
|
|
|
| Message |
| Description | Action |
|
| DO NOT POWER | The Wireless Telephone is in a | None. Do not remove the Battery |
| |
| OFF | critical section of the software | Pack or attempt to power off the |
| |
|
| update. |
| handset while this is displayed. |
|
|
|
|
| Doing so may require the handset |
|
|
|
|
| to be returned to SpectraLink to be |
|
|
|
|
| recovered. |
|
|
|
|
|
| |
| Duplicate IP | The Wireless Telephone has | If using DHCP, check that the |
| |
|
| detected another device with its | DHCP server is properly |
| |
|
| same IP Address. | configured to avoid duplicate |
| |
|
|
|
| addresses. |
|
|
|
|
| If using Static IP, check that the |
|
|
|
|
| Wireless Telephone was assigned |
|
|
|
|
| a unique address. |
|
|
|
|
|
| |
| Erase Failed | Download process failed to erase the | Operation will retry but may |
| |
|
| memory in the Wireless Telephone. | eventually report the error "int. |
| |
|
|
|
| error: 0F" Power cycle the handset. |
|
| Erasing Memory | Wireless Telephone has determined | None. When the progress bar fills |
| |
|
| that a download should occur and is | the display line the erase operation |
| |
|
| erasing the current software from | is complete. |
| |
|
| memory. |
|
| |
| Initializing … | The Wireless Telephone is | None. This is informational only. |
| |
|
| performing power on initialization. |
|
| |
|
|
|
|
| |
| Internal Err. # # | The Wireless Telephone has | Record the error code so it can be |
| |
|
| detected a fault from which it cannot | reported. |
| |
|
| recover. |
| Turn the Wireless Telephone off |
|
|
|
|
| then on again. |
|
|
|
|
| If error persists, try registering a |
|
|
|
|
| different Wireless Telephone to |
|
|
|
|
| this telephone port. |
|
|
|
|
| If error still persists, contact |
|
|
|
|
| SpectraLink Technical Support and |
|
|
|
|
| report the error. |
|
|
|
|
|
| |
| Network Busy | All APs are full or busy. | Try call again later. |
| |
|
|
|
|
| |
| No Host IP | The Wireless Telephone is | Enter a valid IP Address in the |
| |
|
| configured for “static IP” (as opposed | configuration settings or change to |
| |
|
| to “use DHCP”) and no valid host IP | “use DHCP”. |
| |
|
| Address (the Wireless Telephone’s |
|
| |
|
| IP Address) has been entered. |
|
| |
| No IP Address | Invalid IP. | Check the IP Address of the |
| |
|
|
|
| Wireless Telephone and re- |
|
|
|
|
| configure if required. |
|
|
|
|
|
| |
| No PBX Response | The Wireless Telephone tried to | Verify the supported Mitel |
| |
|
| send a message to the supported | Networks VoIP solution is |
| |
|
| Mitel Networks VoIP solution and | operational and connected to the |
| |
|
| failed to get a response. | network. |
| |
|
|
|
|
|
|
PN: | Page 43 |