1. Identify the Right Handrail (86), which is marked | 1 |
|
|
|
|
|
|
|
with a sticker. Have a second person hold the |
|
|
|
|
| Wire Tie | ||
Right Handrail near the tube on the Base (79). |
|
|
|
|
|
| ||
See the inset drawing. Tie the wire tie in the |
|
|
|
|
|
|
|
|
Right Handrail securely around the end of the |
|
|
|
|
|
|
|
|
Wire Harness (84). Then, pull the other end of |
|
|
|
|
|
|
|
|
the wire tie until the Wire Harness is routed |
|
|
|
|
|
|
|
|
completely through the Right Handrail. |
|
|
|
|
|
|
|
|
Gently pull on the Wire Harness (84) while slid- | 34 |
|
|
|
|
|
|
|
ing the Right Handrail (86) down into the tube |
|
|
|
|
|
|
| |
on the Base (79). Make sure not to pinch the |
|
|
|
| 86 |
|
|
|
Wire Harness. |
|
|
|
|
|
|
| |
Attach the Right Handrail (86) to the Base (79) |
|
|
|
|
|
|
|
|
with two M8 x 16mm Bolts (1) and two M8 Star | 1 |
|
|
|
|
|
|
|
Washers (5); do not fully tighten the Bolts |
|
|
|
|
|
|
| |
yet. Be careful not to pinch the Wire Harness | 5 |
|
|
|
|
|
|
|
(84). |
|
|
|
|
| 84 |
| |
Attach the Left Handrail (34) to the Base (79) |
|
|
|
|
|
|
| |
with two M8 x 16mm Bolts (1) and two M8 Star |
|
|
|
|
|
|
|
|
Washers (5); do not fully tighten the Bolts | 86 |
|
|
|
|
|
|
|
yet. |
|
| Wire |
|
|
|
| |
Remove the wire tie from the Wire Harness (84). | 84 |
|
|
| 79 | 5 | 1 | |
|
|
| Tie |
| ||||
2. Orient the Handrail Crossbar (83) as shown. | 2 |
|
|
|
|
|
|
|
See the inset drawing in step 1. Tie the wire tie |
|
|
| Hole |
|
|
| |
in the Handrail Crossbar securely around the |
|
|
|
| 83 |
|
| |
end of the Wire Harness (84). Then, pull the |
|
|
|
|
|
|
| |
other end of the wire tie until the Wire Harness |
|
|
| 84 |
|
|
|
|
is routed completely through the Handrail |
|
|
|
|
|
|
| |
Crossbar. |
| 4 | 2 | Wire Tie |
|
|
|
|
Gently pull on the Wire Harness (84) while in- | 85 |
|
|
|
|
| ||
serting the Handrail Crossbar (83) down into the |
|
|
|
|
|
|
| |
Handrails (34, 86). Make sure not to pinch the |
|
|
|
|
|
|
|
|
Wire Harness. |
|
|
|
|
| 4 |
|
|
Attach the Handrail Crossbar (83) with two M6 x |
|
|
| 85 |
| 2 |
| |
10mm Bolts (2) and two 1/4" Star Washers (4); | 34 |
|
|
|
|
| ||
do not fully tighten the Bolts yet. You may |
|
|
|
|
|
|
| |
need to push the Foam Grips (85) down slightly. |
|
|
|
|
| 86 |
| |
|
|
|
|
|
|
| ||
| 7 |
|
|
|
|
|
|
|