Weslo 831.24822.0 manual Troubleshooting, Compatible with GFCI-equipped outlets

Page 18

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the back cover of this manual. PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 11). Use only a single-outlet surge suppres-

sor that meets all of the specifications described on page 11. IMPORTANT: The treadmill is not

compatible with GFCI-equipped outlets.

 

 

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the power switch located on the treadmill

c

 

frame near the power cord. If the switch protrudes

 

as shown, the switch has tripped. To reset the

 

 

switch, wait for five minutes and then press the

Tripped

Reset

switch back in.

PROBLEM: The power turns off during use

 

 

SOLUTION: a. Check the power switch (see the drawing above). If the switch has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, please see the back cover of this manual.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE

a

 

20

POWER CORD. Remove the three indicated M4.2 x

65

19mm Washer Head Screws (20) and two M5.5 x

 

 

25mm Screws (25). Then, carefully remove the Hood

 

 

 

(65).

 

25

 

 

 

 

Locate the Reed Switch (89) and the Magnet (62) on the left side of the Pulley (71). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If necessary, loosen the M4.2 x 13mm Tek Screw (3), move the Reed Switch slightly, and then retighten the Screw. Reattach the Hood (not shown), and run the treadmill for a few minutes to check for a correct speed reading.

1/8 in.

 

71

89

62

Top View

 

 

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Treadmill Exerciser Model No Serial NoTable of Contents Important Precautions Instructions Before YOU Begin Assembly Make sure the power cord is unplugged. With Console Wire 110 Bracket Page Console Assembly 105 101 103 Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleInsert the key into the console HOW to Turn on the PowerHOW to USE the Manual Mode Start the walking beltMeasure your heart rate if desired When you are finished exercising, removeLower left Lower right disHOW to USE a Preset Workout HOW to Change the Incline of the Treadmill HOW to USE the Upper Body ArmsHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill HOW to Lower the Treadmill for USETroubleshooting Problem The power turns off during useCompatible with GFCI-equipped outlets Problem The walking belt slows when walked on Walking belt. If the walking belt has shifted toProblem The upper body arms squeak during use Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyPart LIST-Model No Qty DescriptionBack cover of this manual. If a part is missing, call R0910A Exploded Drawing B-Model No Exploded Drawing C-Model No Exploded Drawing D-Model No DAY Full Warranty Sears, Roebuck and Co., Hoffman Estates, IL
Top Page Image Contents