Korg 2 manual Global mode, User GE Memory Protect, Midi Clock, RT Realtime Command

Page 23

Global mode

User GE Memory Protect

A protect setting for user GE memory has been added to Memory Protect (1. -2b ☞PG p.136) in the GLOBAL . -2: Pref. (System Preference) page.

User GE (KARMA User GE)

[Off, On]

Protects the user GE memory in internal memory.

On (checked): The internal user GE memory will be protected, and the following writing operations will not be permitted.

•Receiving user GE data via MIDI data dump

•Loading user GE data from disk

Off (unchecked): You will be able to write to internal user GE memory.

RT (Realtime Command)

An “RT (Realtime Command)” check box has been added to GLOBAL . -1a: MIDI Setup (☞PG p.137).

RT (RealTime Command)

[Off, On]

Off (unchecked): MIDI common messages and realtime messages (song position pointer, start, continue, stop) will not be received from the MIDI IN connector when “MIDI Clock” is set to External or Auto. (Song select messages will be received.)

Turn this Off if the song settings of KARMA music workstation are being unintentionally reset by messages from an external MIDI sequencer. You can use this so that the KARMA music workstation ignores the MIDI Start and Stop commands of an external sequencer, yet still responds to MIDI Clock while in external sync mode.

MIDI Clock

The GLOBAL . -1a: MIDI Setup (☞PG p.137) “MIDI Clock” parameter now has an additional setting of Auto.

S/S Out P/C (Start/Stop Out P/C)

A new parameter “S/S Out P/C (Start/Stop Out P/C)” has been added to GLOBAL . -1b: MIDI Filter (☞PG p.138).

MIDI Clock

[Internal, External, Auto]

Auto: Operation will normally be the same as Internal. With the Auto setting, operation will automatically switch to the equivalent of the External setting when MIDI clock messages are received from an external MIDI device connected to the MIDI IN connector.

For details on the Internal and External settings, refer to ☞PG p.137.

You can use this to keep the KARMA in external sync mode while working with an external sequencer, yet still be able to start and play the KARMA function while the external sequencer is not running or sending MIDI clock.

If no further MIDI clock message is received within 500 ms after receiving a MIDI clock, start, or continue message from MIDI IN, or if you start the KARMA music workstation by operating the front panel, operation will switch to the equivalent of Internal.

S/S Out P/C (Start/Stop Out P/C)

[Off, On]

In Program and Combination modes, this function transmits a MIDI start message when you trigger the KARMA function, and a MIDI stop message when you turn it off. This lets you make an external MIDI sequencer or rhythm/groove machine start playing at the moment that the KARMA function begins playing.

Off (unchecked): MIDI “Start” and “Stop” messages will not be sent in Program and Combination mode. Normally you will leave this Off (unchecked) when not slaving external devices.

On (checked): MIDI system realtime messages “Start” and “Stop” will be transmitted in Program and Combination mode. If “MIDI Clock” (PG . -1a ☞PG p.137, ☞p.22) is set to Internal or Auto (and operating as Internal), the start and stop messages will be transmitted under the conditions described below. This can be used to simultaneously start an external MIDI sequencer or rhythm/groove machine at the moment the KARMA function begins playing.

Start: If the [KARMA ON/OFF] key is on, the MIDI system realtime message “Start” will be transmitted at the moment you use the keyboard or CHORD TRIGGER 1–4 keys to trigger the GE selected for a KARMA module.

“Start” will be transmitted at the moment that the GE phrase or pattern is triggered according to the “KARMA Key Zone” (Program, Combination 6.1-2a) setting for that KARMA module.

22

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Page Table of Contents Conventions in this manual About this manualKarma function Main features of versionIntroduction Disk mode Installing the systemSequencer mode Global modeUpdating the GE data After updating the system, you must also update the GE dataYou must update the GE data after updating the system Updating the system dataKarma Time Sig. Karma Time Signature Karma functionGE Select Select by CategoryTxFltr TxFilter Freeze RandomizeParm3 Parameter3 RTC Karma RealTime ControlsHow the Start Seed value affects the phrase 3a Freeze RandomizeStart Seed 2147483648…0 Random…+2147483647 Freeze Loop Length Off, 1…32Link Start Seeds Off, On Random CaptureRetrigger Each Time Off, On Random FF/REW ProcedureAuto K.RT Name Auto Assign Karma RT Name Auto Assign Karma RT NameRT Parameter RealTime Parameter Grp Parm Group Off, Mix, Ctrl, Trig, Zone, Rand, PECopy Scene 1&2 Copy Karma Scene AutoName w/GEchgCopy/Swap Karma Scene AutoName w/GEchg Auto Assign Karma RT Name on GE changeGE Generated Effect Group Phase GroupGE Parameter Step Transpose On/Off Beginning Offset %/End Offset %Pattern Parameters Step Transpose Value 48…0…+48Swing% Duration ModeRhythm Group Duration GroupCCs Group Associated Parameters Drum Group123456a Destination -6, Value Sequencer modeSEQ .3 Tone Adjust Destination -6 and Value1b Utility Sequencer modeMulti REC Standby Off, On Copy From Prog Copy from ProgramEnhancements Multi REC Standby check boxUtility menu Auto Song Setup functionQuantize Swing Parameter Other enhancementsMidi Clock Global modeRT Realtime Command User GE Memory ProtectFoot Pedal Assign Dump User GEFoot SW Assign Additional Load functions Disk modeLoad Load .PCGChanges and additions to the Save function SaveData compatibility Program, Combination, Sequencer, Song Play parameters Sequencer mode Tone Adjust parametersGlobal mode settings that were added in version Copy From Program Combination mode Copy from ProgramOther functions Tap Tempo ControlData dump request song, track, measure region from Program modeAbout system exclusive messages 15-12, Shimotakaido 1-chome, Suginami-ku, Tokyo, Japan Important Notice to Consumers
Top Page Image Contents