Korg manual 3a Freeze Randomize, Start Seed 2147483648…0 Random…+2147483647

Page 9

The display in Combination mode

6.2–3a

6.2–3a: Freeze Randomize

In modes where you can use more than one KARMA module (Combination, Sequencer, and Song Play modes),

use the [ ]/[ ] keys to select the KARMA module for which you want to set the Freeze Randomize parameters.

Start Seed

[-2147483648…0: Random…+2147483647]

Specifies the seed that is used by the KARMA module to generate the random phrase.

Seed” is the source data from which the randomiza- tions are created. “Start Seed” is the seed that will be used each time a trigger occurs.

The 6.4-6(7): Random 1(2) settings in Combination, Sequencer, and Song Play modes are valid regardless of the “Start Seed” setting. If you select the same GE and specify the same “Start Seed” value for KARMA modules A, B, C, and D, the phrase after being triggered will be the same, but the way in which it changes for each repetition will depend on the Random 1 (2) settings.

0:Random: A different phrase will be generated each time the trigger occurs. Within the KARMA module, a different “Start Seed” value is specified randomly each time the trigger occurs. In system version 1.0, this is the setting that is always used.

Any value other than Random: The same phrase will be generated each time the trigger occurs. Different values for the Start Seed parameter will produce different phrases, but the same phrase will always be generated if the Start Seed value is the same.

How the “Start Seed” value affects the phrase

As an example, we will use the combination E-67: Modern Jazz [JS] to see how different “Start Seed” settings will affect the phrase.

1In Combination mode, select E067: Modern Jazz [JS].

E067: Modern Jazz [JS] is a combination in which a sax solos over backing provided by drums, bass, and piano.

2Press the [MENU] key, and select the 6.2: Ed-KARMA Mdl page. (For details on how to select a page, PG p.1)

3Press the [F3] key to select the Parm3 page.

4Use the [ ]/[ ] keys to select Module A, and make sure that “Start Seed” is set to 0: Random. If “Start Seed” is not set to 0: Random, change the setting to 0: Random. Module A will generate a phrase for the sax of timbre 2.

5Use the CHORD TRIGGER [1] key to trigger the GE several times at a regular interval (one or two seconds). Pay attention to the sax phrase that begins immediately after each trigger. The sax will begin playing a different phrase each time the trigger occurs.

6Change the “Start Seed” to any value other than 0: Random. For this example, set it to +1.

7In the same way as you did in step 5, use the CHORD TRIGGER [1] key to trigger the GE several times, and pay attention to the sax phrase that begins immediately after each trigger. The sax will begin playing the same phrase each time the trigger occurs.

8Change the “Start Seed” to a value other than +1, and perform the same actions as you did in step 5. The sax will begin playing the same phrase each time the trigger occurs, but it will be a different phrase than when “Start Seed” was set to +1.

If you set “Start Seed” to 0: Random, and execute “Random Capture” (p.9) after triggering, the “Start Seed” value that was internally set within the module at the time of triggering will be specified here. While listening to the phrases that change randomly at each trigger, you can execute this when you hear a phrase that you want to reproduce. In conjunction with the “Freeze Loop Length” setting, you can also loop a phrase that you like. (p.10 Checking the Freeze Randomize function, and performing “Random Capture”using the “Random FF/REW” function)

Freeze Loop Length

[Off, 1…32]

Specifies the number of measures in the phrases that are repeatedly generated by the KARMA module. After being triggered, the module will generate a phrase of the number of measures you specify here, and will then repeat that phrase. If you set this Off, the phrase will not be repeated.

The table below and the explanations that follow describe how various combinations of “Start Seed” and “Freeze Loop Length” settings will affect the phrase or control data that is randomly generated by the KARMA module each time triggering occurs, according to the GE settings you are using.

 

“Start Seed”

“Freeze Loop Length”

 

 

 

(1)

0: Random

Off

(2)

any value

Off

(3)

0: Random

1...32

(4)

any value

1...32

(1)“Start Seed”: 0: Random, “Freeze Loop Length”: Off The phrase will change randomly each time triggering occurs. Each time the phrase repeats, it will change randomly. This is what happens in system version 1.0. For example, suppose there is a GE that, if you input C-D-E-F, will randomly vary the order of notes, and repeatedly play four notes in each measure. When you trigger this GE, it produces notes in a random order of (for example) C-D-E- F, C-C-D-F, F-D-C-E…. When you trigger this GE again, it produces a different random phrase of (for example) E-D-C-C, C-C-D-D, C-D-C-E....

8

Image 9
Contents Page Table of Contents Conventions in this manual About this manualMain features of version IntroductionKarma function Sequencer mode Installing the systemGlobal mode Disk modeYou must update the GE data after updating the system After updating the system, you must also update the GE dataUpdating the system data Updating the GE dataGE Select Karma functionSelect by Category Karma Time Sig. Karma Time SignatureParm3 Parameter3 Freeze RandomizeRTC Karma RealTime Controls TxFltr TxFilterStart Seed 2147483648…0 Random…+2147483647 3a Freeze RandomizeFreeze Loop Length Off, 1…32 How the Start Seed value affects the phraseRandom Capture Retrigger Each Time Off, OnLink Start Seeds Off, On Random FF/REW ProcedureRT Parameter RealTime Parameter Auto Assign Karma RT NameGrp Parm Group Off, Mix, Ctrl, Trig, Zone, Rand, PE Auto K.RT Name Auto Assign Karma RT NameCopy/Swap Karma Scene AutoName w/GEchgAutoName w/GEchg Auto Assign Karma RT Name on GE change Copy Scene 1&2 Copy Karma ScenePhase Group GE ParameterGE Generated Effect Group Pattern Parameters Beginning Offset %/End Offset %Step Transpose Value 48…0…+48 Step Transpose On/OffRhythm Group Duration ModeDuration Group Swing%CCs Group Associated Parameters Drum GroupSEQ .3 Tone Adjust Sequencer modeDestination -6 and Value 123456a Destination -6, Value1b Utility Sequencer modeEnhancements Copy From Prog Copy from ProgramMulti REC Standby check box Multi REC Standby Off, OnQuantize Swing Parameter Auto Song Setup functionOther enhancements Utility menuRT Realtime Command Global modeUser GE Memory Protect Midi ClockDump User GE Foot SW AssignFoot Pedal Assign Load Disk modeLoad .PCG Additional Load functionsSave Data compatibilityChanges and additions to the Save function Sequencer mode Tone Adjust parameters Global mode settings that were added in versionProgram, Combination, Sequencer, Song Play parameters Other functions Combination mode Copy from ProgramTap Tempo Control Copy From ProgramProgram mode About system exclusive messagesData dump request song, track, measure region from 15-12, Shimotakaido 1-chome, Suginami-ku, Tokyo, Japan Important Notice to Consumers