Heath Zenith 9600LED series warranty Troubleshooting Guide, Symptom Possible Cause Solution

Page 7

TROUBLESHOOTING GUIDE

SYMPTOM

POSSIBLE CAUSE

SOLUTION

 

 

 

 

 

 

 

 

 

 

Lights will not come

1.

Light switch is turned off.

1.

Turn light switch on.

on.

2.

Lamp is loose or burned out.

2.

Check lamp and replace if burned out.

 

3.

Fuse is blown or circuit breaker is turned

3.

Replace fuse or turn circuit breaker on.

 

 

off.

 

 

 

4.

Daylight turn-off is in effect.

4.

Recheck after dark.

 

5.

Incorrect circuit wiring, if this is a new

5.

Verify wiring is correct.

 

 

installation.

 

 

 

 

 

 

 

Lights come on in

1.

Light control may be installed in a relatively

1.

The fixture is operating normally under these

daylight.

 

dark location.

 

conditions.

 

2.

Light control is in TEST.

2.

Set control switch to 5 or 10 minutes or Dusk-to-

 

 

 

 

Dawn.

 

 

 

Lights come on for no

Light control may be sensing small animals or

Reduce sensitivity.

apparent reason.

automobile traffic.

 

 

 

 

 

 

 

Lights stay on continu-

1.

The sensor may be picking up a heat source

1.

Reduce sensitivity.

ously.

 

like an air vent, dryer vent, or brightly

 

 

 

 

painted, heat-reflective surface.

 

 

 

2.

Sensor is in Automatic Override or Manual

2.

Set control switch to 5 or 10 minutes.

 

 

Override mode.

 

 

 

 

 

 

 

Lights flash on and

1.

Heat being reflected from other objects

1.

Reduce sensitivity.

off.

 

may be affecting the sensor.

 

 

 

2.

Sensor is in the Test mode.

2.

While in TEST mode, light only stays on for 5

 

 

 

 

seconds.

 

 

 

Light does not stay on

Nearby large, light-colored objects reflecting

Do not point other lights at the sensor.

in Manual mode.

light may trigger the shut-off feature.

 

 

 

 

 

 

 

598-1338-03

7

Image 7
Contents Unpacking FeaturesInstallation RequirementsRecommended Grounding Method WiringMasterSlave Optional WiringMasterMaster Final Assembly Turn on the circuit breaker and light switch Testing and AdjustmentsOperation Manual override Mode Adjustment of Coverage AreaSpecifications Mode Switching SummarySymptom Possible Cause Solution Troubleshooting GuideTWO Year Limited Warranty Desempaque CaracterísticasInstalacion RequisitosAdvertencia Desconecte la energía en el cortacircuito CableadoMétodo recomendado de conexión a tierra Maestra Esclava Conexion AlternaMaestra Maestra Bombillas Montaje del aparato Vatios máximo Cada una Conecte el disyuntor y el interruptor de la luz Pruebas Y AjustesRegulación DEL Área DE Cobertura OperaciónResumen de las modalidades Del interruptor Fase de Sobre control ManualGuia DE Investigacion DE Averias EspecificacionesGarantía Limitada DE DOS Años Exigences CaractéristiquesDéballage Câblage Méthode de mise à la terre recommandéeMaître Satellite Câblage FacultatifMaîtreMaître Assemblage Final InstallationRé-enclenchez le disjoncteur puis ouvrez l’interrupteur Essais ET RéglagesFonctionnement Mode Contournement ManuelRéglage DE LA Zone DE Couverture Ment Manuel Fiche TechniqueGuide DE Dépannage Contournement AutoGarantie Limitée DE Deux ANS