NordicTrack NTL12840 user manual

Page 7

3.Cut the rubber band securing the Upright Wire Harness (98). Have a second person hold the console assembly near the Uprights (69). Connect the Upright Wire Harness to the wires extending from the Console Base (81). The connectors should slide together easily and snap into place. If they do not, turn one connector and try again. Insert the connectors and the Upright Wire Harness down into the right Upright, and then set the console assembly on the Uprights. Be careful not to pinch the wires.

4.Insert a Handrail (118) into the right side of the console assembly as shown. (Note: It may be helpful to twist the Handrail as you insert it.) Next, insert two 4 1/2” Bolts (78) with Handrail Spacers (77) into the right Upright (69) and the Handrail. Be careful not to pinch the wires. Make sure that the Handrail Spacers are flush against the right Upright, with the thicker sides of the Handrail Spacers toward the center of the treadmill, as shown in the inset drawing.

Next, lift the console assembly and the Handrail (118) slightly and align the 4 1/2” Bolts (78) with the holes in the Handrail. Thread the Bolts into the Handrail until the heads of the Bolts are against the right Upright (69). Do not tighten the Bolts yet.

Attach the other Handrail (not shown) in the same way. Note: There are no wires on the left side.

5.With the help of a second person, carefully tip the Uprights (69) down to the position shown. Make sure that the Extension Legs (102) remain in the Uprights.

Attach each Extension Leg (102) with two 1” Screws (47) and a Base Pad (99) as shown. Note: Attach the lower Screw (without the Base Pad) first.

Next, align the lower ends of the Handrails (118) with the holes in the base of the Uprights (69). Attach each Handrail with a 4” Bolt (53) as shown. Note: The Bolts must be at an angle that matches the angle of the Handrails, as shown in the inset drawing.

Note: A replacement Base Pad (99) may be included. Use the Base Pad to replace any Base Pad that becomes worn.

3

 

 

98

 

 

 

 

 

81

 

 

98

 

 

 

 

69

 

Console

 

 

 

Assembly

 

 

 

4

 

 

 

 

 

69

Thick

 

 

77

 

 

 

Side

118

 

 

 

 

77

78

 

 

Console

 

 

 

Assembly

 

 

5

 

 

 

 

 

 

99

69

 

 

53

 

 

 

 

 

 

99

 

99

102

47

 

 

99

 

53

 

 

 

 

118

99

 

 

 

 

 

 

47

 

53

102

 

 

99

 

 

 

 

 

 

 

118

 

7

Image 7
Contents Model No. NTL12840 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions Page Right Side Before YOU BeginAssembly Page PLS2 HOW to Plug in the Power Cord Operation and AdjustmentPerformant Lubetm Walking Belt Features of the Console HOW to USE the Manual Mode HOW to Turn on the PowerCalories/Fat Calories Change the incline of the treadmill as desiredFollow your progress with the displays Program Incline/Heart RateSelect one of the preset programs HOW to USE Preset ProgramsMeasure your heart rate if desired Whenkey. you are finished exercising, remove Follow your progress with the displaysSelect one of the custom programs HOW to Create Custom ProgramsHOW to USE Custom Programs Put on the optional chest pulse sensor HOW to USE Heart Rate ProgramsSelect a heart rate program Enter your age Adjust the maximum speed limit for ProgramHOW to Connect Your Portable Stereo HOW to Connect Your Computer HOW to Connect Your Home StereoHOW to Connect Your VCR Measure your heart rate if desired Follow the on-line instructions to start Program HOW to USE Programs Directly from OUR WEB SiteReturn to the treadmill and stand on the foot Optional Chest Pulse Sensor Information MODE/DEMO ModeHOW to USE the Aromatherapy System HOW to Adjust the Cushioning SystemHOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingTop View Problem The walking belt slows when walked on Exercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesQty Description R1003AOrdering Replacement Parts DRAWING-Model Exploded DRAWING-Model No Limited Warranty