NordicTrack NTL06907.1 user manual Troubleshooting, Problem The power turns off during use

Page 26

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 12). Use only a single-outlet surge suppres- sor that meets all of the specifications described on page 12. Important: The treadmill is not com- patible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c.Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

PROBLEM: The power turns off during use

c

Tripped

Reset

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, please see the back cover of this manual.

PROBLEM: The incline of the treadmill does not change correctly

SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re- move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. Remove the three 3/4" Screws (12) and carefully pivot the Hood (61) off.

12

61

26

Image 26
Contents Call TOLL-FREE QUESTIONS?Model No. NTL06907.1 Serial No Table of Contents Important Precautions Page Before YOU Begin Hardware may be included AssemblyMake sure that the power cord is unplugged Do not fully fold the Frame yetCareful not to pinch the Upright Wire Fully tighten the Bolts yetDo not fully tighten the Bolts yet Not fully fold the Frame yetNut the Wheel must turn freely. Discard Connected PROPERLY, the Console MAY be Damaged When the Power is Turned onSole MAY be Damaged When Power is Turned on Not Connected PROPERLY, the CONPage Make sure that no wires are pinched PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleSelect the user mode HOW to Turn on the PowerHOW to Personalize Console Settings Set the date and time Select a default user settingHOW to Identify Yourself AS User 1 or User HOW to USE the Manual Mode HOW to USE a Preset Workout or a Weight Loss Workout Press the Start button to start the workout HOW to Create a Learn Workout Select a learn workoutHOW to USE a Learn Workout Change the workout if desired HOW to View the Fitness Journal Exit the user mode HOW to Reset the Fitness JournalSelect the user mode. See on Reset the fitness journal Information ModeHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Page Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyR1007A Key No. Qty DescriptionQty Exploded Drawing A-Model No. NTL06907.1 Exploded Drawing B-Model No. NTL06907.1 Exploded Drawing C-Model No. NTL06907.1 Exploded Drawing D-Model No. NTL06907.1 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty