NordicTrack NTL09107.0 user manual Assembly

Page 9

7.Remove the plastic ties from the handrail assem- bly. If necessary, press the Cage Nuts (33) into place.

With the help of a second person, hold the handrail assembly near the Right Upright (78) and the Left Upright (74). Connect the Upright Wire (38) to the console wire. See the inset drawing. The connectors should slide to- gether easily and snap into place. If they do not, turn one connector and try again. IF THE

CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAM- AGED WHEN THE POWER IS TURNED ON.

Remove the wire tie from the Upright Wire (38).

Set the handrail assembly on the Uprights (74, 78). Be careful not to pinch the wires.

8.Attach the handrail assembly to the Uprights (74, 78) with six 5/16" x 1 1/4" Bolts (7) and six 5/16" Star Washers (10) as shown. Start all six

Bolts before tightening them.

See assembly steps 4 and 6. Firmly tighten the 3/8" x 4 1/2" Bolts (6).

9.With the help of a second person, hold the con- sole assembly near the handrail assembly. Connect the two wires from the console assem- bly to the two wires from the handrail assembly.

See the inset drawing in step 7. The connec- tors should slide together easily and snap into place. If they do not, turn one connector and try again. IF THE CONNECTORS ARE

NOT CONNECTED PROPERLY, THE CON- SOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON.

7

			Handrail
			Assembly
	33
	Plastic	74
	Tie	74
	Tie
		33
	Console	Plastic	38
		Tie	38
		Tie
	Wire
			Console
	38		Wire

Wire Tie

				78
8				Handrail
				Assembly
		10
7	10	7	7
	10		7

			10
		74		10
				10
			7	78
9
		Console
		Assembly

Wires

Wires

Handrail

Assembly

9

Image 9

Contents QUESTIONS? Model No. NTL09107.0 Serial NoCall TOLL-FREE Table of Contents Important Precautions Page Before YOU Begin Assembly See the inset drawing. Tie the wire tie Make sure that the power cord is unpluggedDo not fully fold the Frame yet Nut the Wheel must turn freely. DiscardFully tighten the Bolts yet Be careful not to pinch the Upright WireAssembly Pull on the sleeve to make sure that it is locked into place Be careful not to pinch the wires. Reattach Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerSelect the manual mode Start the walking belt and adjust the speedChange the incline of the treadmill as desired Time/Incline disDistance Measure your heart rate if desired HOW to USE a Preset Workout Select a preset workoutPress the Start button to start the workout HOW to USE the Custom Workout Center Select the Custom Workout CenterPress the Start Workout button to start the workout Put on the chest pulse sensor HOW to USE the Fitness Test WorkoutSelect the fitness test workout Press the Start Fitness Test button to start the workoutHOW to USE the Stereo Sound System Insert an iFIT card and select a workout HOW to USE AN Ifit CardInformation Mode HOW to Adjust the Cushioning SystemOptional Chest Pulse Sensor HOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Page Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Key No. Qty Description R0308AQty Exploded Drawing A-Model No. NTL09107.0 Exploded Drawing B-Model No. NTL09107.0 Exploded Drawing C-Model No. NTL09107.0 Exploded Drawing D-Model No. NTL09107.0 Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT