NordicTrack NTL18907.0 HOW to USE AN Ifit Card, Insert an iFIT Card and select a program

Page 22

HOW TO USE AN IFIT CARD

1 Insert the key into the console.

See HOW TO TURN ON THE POWER on page 12.

2 Personalize console settings if desired.

See HOW TO PERSONALIZE CONSOLE SET- TINGS on page 12.

3 Insert an iFIT Card and select a program.

To use an iFIT program, insert an iFIT Card into the iFIT slot; make sure that the iFIT Card is ori- ented so the metal contacts are face-down and are inserted into the iFIT slot.

iFIT Slot

iFIT Card

Next, select an iFIT program by pressing the iFIT increase and decrease buttons (next to the lit iFIT indicator). When an iFIT program is selected, the display will show the name of the program, the maximum incline setting and the maximum speed setting of the program, and the program time. In addition, a profile of the speed settings of the pro- gram will appear in the display.

Each preset program is divided into several one- minute segments. One speed setting and one in- cline setting are programmed for each segment. Note: The same speed setting and/or incline set- ting may be programmed for two or more consec- utive segments.

4 Press the Start button to start the program.

A moment after the button is pressed, the tread- mill will automatically adjust to the first speed and incline settings of the program. Hold the handrails and begin walking.

Select a display mode and monitor your

5 progress with the display and the training zone bar.

When an iFIT program is selected, the console of- fers three display modes (see step 6 on pages 14 and 15). Press the Display button repeatedly to se- lect the desired display mode. If the first or sec- ond display mode is selected, a profile of the speed settings of the program will appear in the dis- play. A small arrow below the profile will indicate your progress.

During the program, a personal trainer will guide you through the workout. You can adjust the vol- ume or select an audio setting for your personal trainer (see step 4 on page 13).

If the speed or incline setting for the current seg- ment is too high or too low, you can override the setting by pressing the Speed or Incline buttons; however, when the next segment begins, the treadmill will automatically adjust to the speed and incline settings for the next segment.

To stop the program at any time, press the Stop button. To restart the program, press the Start but- ton. The walking belt will begin to move at 1 mph. When the next segment of the program begins, the treadmill will automatically adjust to the speed and incline settings for the next segment.

6 Turn on the fan if desired.

See step 8 on page 15.

When you are finished exercising, remove the

7 key from the console.

See step 8 on page 17.

CAUTION: Always remove iFIT Cards from the iFIT slot when you are not using them.

22

Image 22
Contents Model No. NTL18907.0 Serial No QUESTIONS?Call TOLL-FREE Table of Contents Important Precautions Page Before YOU Begin Assembly Try again. if the Connectors are not Bly. Make sure to connect the connectorsHandrail Bolts before tightening them Page 105 Wire Cylinder HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleSelect the user mode HOW to Turn on the PowerHOW to Personalize Console Settings Enter user informationSelect the settings mode HOW to USE the Manual Mode Measure your heart rate if desired Turn on the fan if desiredSelect a Cardio program HOW to USE a Cardio ProgramPress the Start button to start the program See on Adjust the maximum target heart rate setting if Desired HOW to USE a Pulse ProgramSelect a Pulse program Turn on the fan if desired HOW to Create a Record Program Select a Record programHOW to USE a Record Program HOW to USE AN Ifit Card Insert an iFIT Card and select a programPage HOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingTop Problem The walking belt slows when walked on Workout Guidelines Conditioning GuidelinesExercise Intensity Exercise FrequencySuggested Stretches R1206A Qty DescriptionOrdering Replacement Parts Exploded Drawing A-Model No. NTL18907.0 Exploded Drawing B-Model No. NTL18907.0 Exploded Drawing C-Model No. NTL18907.0 Exploded Drawing D-Model No. NTL18907.0 Limited Warranty