NordicTrack A2750 PRO warranty Troubleshooting, Outlets, Problem The power turns off during use

Page 25

TROUBLESHOOTING

Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, see the front cover of this manual. PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 14). Use only a single-outlet surge suppres-

sor that meets all of the specifications described on page 14. IMPORTANT: The treadmill is not

compatible with GFCI-equipped outlets and may not be compatible with AFCI-equipped

outlets.

 

 

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the power switch located on the treadmill

c

 

frame near the power cord. If the switch protrudes

 

as shown, the switch has tripped. To reset the

Tripped

Reset

switch, wait for five minutes and then press the

switch back in.

 

 

PROBLEM: The power turns off during use

 

 

SOLUTION: a. Check the power switch (see the drawing above). If the switch has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, please see the front cover of this manual.

PROBLEM: The console displays remain lit when you remove the key from the console

SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a

store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off

the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE

INFORMATION MODE on page 23 to turn off the demo mode.

PROBLEM: The displays of the console do not function properly

 

SOLUTION: a. Remove the key from the console and UNPLUG

a

THE POWER CORD. Place the treadmill in the

storage position (see HOW TO FOLD THE

 

TREADMILL on page 24). Remove the two #8 x

 

1 1/2" Screws (52).

52

Then, lower the treadmill (see HOW TO LOWER

THE TREADMILL FOR USE on page 24).

52

 

25

Image 25
Contents 1CALL-800TOLL-TO-FREE-BE-FIT QUESTIONS?Model No. NTL01009.4 Serial No On the WEBTable of Contents Important Precautions Instructions Save TheseBefore YOU Begin Assembly Attach the other Wheel 95 in the same way Page Patch Bolts yet Assembly Into the Uprights. Do not tighten the Patch Bolts yet Again. if YOU do not Connect the CONAll sixteen Patch Bolts 4, 5, 8. Slide Raise the Frame 55 to the position shown HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console DiagramConsole AudioHOW to USE the Manual Mode HOW to Turn on the PowerInsert the key into the console Turn on the fan if desired Measure your heart rate if desired. Before usingSelect a preset workout HOW to USE a Preset WorkoutStart the workout See on Select a competition workout HOW to USE a Competition WorkoutSee on HOW to USE the Stereo Sound System HOW to USE the Ifit Live ModeMetric Information ModeHOW to Fold the Treadmill HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USEProblem The power turns off during use TroubleshootingOutlets Top Problem The walking belt slows when walked onView Turn if the walking belt has shifted to Problem SolutionConsole display has lines running through it Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Key No. Qty Description Part ListQty Exploded Drawing a Exploded Drawing B Exploded Drawing C Exploded Drawing D Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT