Horizon Fitness T93 manual S E M B Ly C O N T I N U E D

INTRODUCTION IMPORTANT PRECAUTIONS

ASSEMBLY

BEFORE YOU BEGIN

A S S E M B LY STEP 2 ( C O N T I N U E D )

HARDWARE BAG 2 CONTENTS:

BOLT (D)	FLAT WASHER (E)	WAVY WASHER (F)	LOCK LATCH PIN (G)
Qty: 1	27 mm	29 mm	Qty: 1
	Qty: 1	Qty: 1

	MAIN FRAME	CONSOLE CABLE	RIGHT CONSOLE MAST
		WAVY WASHER (F)	FLAT WASHER (E)
			BOLT (D)
			PRE-ATTACHED NUT
			RIGHT LINKAGE ARM
PRE-ATTACHED
TEFLON WASHER		PRE-ATTACHED BOLT
ELEVATION FRAME
	FOOT LOCK LATCH

A S S E M B LY STEP 3

HARDWARE BAG 3 CONTENTS :
BOLT (H)	SPRING WASHER (I)	FLAT WASHER (J)	ARC WASHER (K)
15 mm	15 mm	19 mm	17 mm
Qty: 4	Qty: 4	Qty: 2	Qty: 2

	CONSOLE CABLES
CONSOLE
ARC WASHER (K)	DO NOT ATTACH
	THIS SIDE UNTIL STEP 3-D
	CONSOLE MAST

IMPORTANT PRECAUTIONS INTRODUCTION

ASSEMBLY

BEFORE YOU BEGIN

TREADMILL

OPERATION

CONDITIONING TROUBLESHOOTING LIMITED

GUIDELINES & MAINTENANCE WARRANTY

10

EInsert 1 bolt (D) and 1 FLAT washer (E) through RIGHT console mast followed by 1 WAVY washer (F) and attach to MAIN FRAME.

FUnscrew PRE-ATTACHED NUT and remove from RIGHT LINKAGE ARM and discard. Carefully move right linkage arm and PRE-ATTACHED TEFLON WASHER into position and attach to ELEVATION FRAME.

Note: While holding RIGHT CONSOLE MAST in the upright position, tighten PRE-ATTACHED BOLT using T-wrench to attach RIGHT LINKAGE ARM.

GCut band holding FOOT LOCK LATCH assembly. Lift the running deck until lock latch on side of treadmill is fully engaged.

HRemove console from box and place out of the way.

ILower the treadmill running deck from the folded position by stepping on LOCK LATCH on lower right side.

Note: If you have attempted to

*move the treadmill from the box and the machine has sprung open and cannot be assembled, refer to the troubleshooting section in order to restore the treadmill to its proper position.

1

3

2

FLAT WASHER (J)

SPRING WASHER (I)

BOLT (H)

AOpen HARDWARE BAG 3.

BWith running deck in lowered position, place console on the console masts. Align the brackets that are underneath the console with the top holes of the console masts.

CTo assemble the Console to the LEFT CONSOLE MAST, insert 1 BOLT (H), 1 SPRING WASHER (I) and 1 FLAT WASHER (J) into the side hole and insert 1 BOLT (H), 1 SPRING WASHER (I) and 1 ARC WASHER (K) into the back hole in the left CONSOLE mast and lightly tighten.

DGently lift right side of the console to connect the console cableS. Carefully tuck wires in mast to avoid damage. NOTE: Do not pinch console cable or grip pulse wires.

ERepeat step C above to assemble the right console mast to the console.

FLeave console bolts loose until after STEP 4 is completed.

11

TREADMILL OPERATION

LIMITED TROUBLESHOOTING CONDITIONING WARRANTY & MAINTENANCE GUIDELINES

T93_Rev.1.5.indd 10-11 6/20/08 2:05:14 PM