Gold's Gym GGTL59608 manual Problem Solution

Page 24

PROBLEM:

SOLUTION:

PROBLEM:

SOLUTION:

The walking belt is off-center or slips when walked on a. If the walking belt is off-center, first remove the

key and UNPLUG THE POWER CORD. If the walking belt has shifted to the left, use the hex key to turn the left idler roller bolt clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the bolt counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walk- ing belt is centered.

b. If the walking belt slips when walked on, first re- move the key and UNPLUG THE POWER CORD. Using the hex key, turn both idler roller bolts clock- wise, 1/4 of a turn. When the walking belt is cor- rectly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walk- ing belt centered. Then, plug in the power cord, in- sert the key, and carefully walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

The crosswalk arms squeak during use

a. (Note: Correcting this problem requires a small amount of white marine grease, available at hard- ware stores.) Turn the Resistance Knob (110) counterclockwise and remove it. Next, remove the Resistance Cone (108) with the Crosswalk Arm (98).

Apply a thin layer of white marine grease to the outer surface of the Resistance Cone (108). Then, reattach the Resistance Cone with the Crosswalk Arm (98) and the Resistance Knob (110).

a

b

a

 

98

 

110

 

108

 

 

24

Image 24
Contents QUESTIONS? Model No. GGTL59608.0 Serial NoTable of Contents Important Precautions Local electronics storePulse sensor is not a medical device Page Before YOU Begin Assembly Make sure that the power cord is unplugged Do not fully fold the Frame yetOvertighten the Locknut the Wheel must Turn freely With a second Bolt Spacer 84, 3/8 x 4 Bolt 3/8 Star Washer Right Upright do not fully tighten the Bolts YetBolts yet 3/4 Bolt 112. Do not fully tighten Resistance Knob Attach the other resistance mechanism toRight Upright 79 as described above Attach the other Crosswalk Arm 98 as deAgain. if the Connectors are not CON PowerCareful not to pinch the wires Be careful not to pinch the wires in the Right Handrail Make sure that no wires are pinched Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeSelect the manual mode Insert the key into the consoleTurn on the fan if desired HOW to USE a Preset Workout Select one of the preset workouts. To select oneStart the workout Information Mode HOW to USE the Stereo Sound SystemHOW to USE the Crosswalk Arms Optional Chest Pulse SensorHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USETroubleshooting Problem The power turns off during useCompatible with GFCI-equipped outlets Problem The walking belt slows when walked on TopProblem Solution Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyPart LIST-Model No. GGTL59608.0 Key No. Qty Description109 Console Fan Userʼs Manual Exploded Drawing A-Model No. GGTL59608.0 R0509B Exploded Drawing B-Model No. GGTL59608.0 R0509B Exploded Drawing C-Model No. GGTL59608.0 R0509B Exploded Drawing D-Model No. GGTL59608.0 Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT