Gold's Gym 685, GGTL58608.0 manual Troubleshooting, Problem The power turns off during use

Page 21

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If you need further assistance, please see the front cover of this manual. PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 11). Use only a single-outlet surge suppres- sor that meets all of the specifications described on page 11. IMPORTANT: The treadmill is not compatible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the reset/off circuit breaker located on the

c

 

treadmill frame near the power cord. If the switch

 

protrudes as shown, the circuit breaker has

 

 

tripped. To reset the circuit breaker, wait for five

Tripped

Reset

minutes, and then press the switch back in.

PROBLEM: The power turns off during use

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, see the front cover of this manual.

PROBLEM: The console displays remain lit when you remove the key from the console

SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a

store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off

the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE

INFORMATION MODE on page 18 to turn off the demo mode.

 

PROBLEM: The display of the console does not function properly

 

 

SOLUTION: a. Remove the key from the console and UNPLUG THE

a

11

POWER CORD. With the help of a second person,

carefully tip the Uprights (70, 76) down as shown.

 

 

Remove the three Screws (11) and two 3/4" Screws

 

70

(23). Note: A Phillips screwdriver with a shaft at least 5

 

in. (13 cm) long is required.

 

23

 

76

23

 

 

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model No. GGTL58608.0 Serial No QUESTIONS?Table of Contents Important Precautions Page Before YOU Begin Assembly Make sure that the power cord is unpluggedFully tighten the Upright Bolts yet Upright do not fully tighten the Upright Bolts Yet See steps 2 and 4. Fully tighten the two Endcap ScrewsTighten the Bolts yet Not Connected PROPERLY, the CON Sole MAY be Damaged When Page Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerTurn on the fan if desired Measure your heart rate if desiredProgram HOW to USE a Personal Trainer QuickSelect one of the personal trainer quick ProgramsHOW to Create Your OWN Quick Program Follow your progress with the matrix and the displaysSelect a custom quick program Select a custom quick programs HOW to USE Your OWN Quick ProgramInformation Mode HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingTop Problem The walking belt slows when walked onProblem Solution Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Key No. Qty. Description R1108AKey No. Qty Description Exploded Drawing A-Model No. GGTL58608.0 R1108A Exploded Drawing B-Model No. GGTL58608.0 R1108A Exploded Drawing C-Model No. GGTL58608.0 R1108A Exploded Drawing D-Model No. GGTL58608.0 R1108A Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents