Healthrider HRTL11940 manual Troubleshooting, Problemsolution

Page 23

TROUBLESHOOTING

Most treadmill problems can be solved by following the instructions below. If further assistance is needed, please call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).

PROBLEMSOLUTION

1.The power does not turn on

a.Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 8). Use only a single-outlet surge suppressor that meets all of the specifications described on page 8. Important: The treadmill is not compatible with GFCI-equipped outlets.

b.Make sure that the key is fully inserted into the console.

c.Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

c

Tripped Reset

2.The power turns off during use

a.Check the reset/off circuit breaker located on the treadmill frame near the power cord (see 1. c. above). If the circuit breaker has tripped, wait for five minutes and then press the breaker back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, un- plug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console and then reinsert it.

3. The walking belt

a. Use only a single-outlet surge suppressor that meets all of the specifications de-

slows when walked

scribed on page 8.

 

 

on

 

 

 

 

b. If the walking belt is overtightened, tread-

b

3–4”

 

mill performance may decrease and the

 

walking belt may be permanently dam-

 

 

 

aged. Remove the key and UNPLUG THE

 

 

 

POWER CORD. Using the included allen

 

 

 

wrench, turn both rear roller adjustment

 

 

 

bolts counterclockwise 1/4 of a turn. When

 

 

 

the walking belt is properly tightened, you

 

 

 

should be able to lift the edges of the

Rear Roller Adjustment Bolts

 

walking belt 3 to 4 inches off the walking

 

 

 

platform. Be careful to keep the walking

 

 

 

belt centered. Plug in the power cord, insert the key and run the treadmill for a few

 

minutes. Repeat until the walking belt is properly tightened.

 

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents
Customer HOT Line QUESTIONS?Model No. HRTL11940 Serial No Table of Contents Important Precautions Page Right Side Before YOU BeginBack Assembly Turn the receiver B so the cylinder is on the side Make sure that no wires are pinched. See aboveUprights 65 as shown, with the Bumpers 98 under Performant Lubetm Walking Belt HOW to Plug in the Power CordTreadmill Operation Features of the Console HOW to USE the Manual Mode HOW to Turn on the PowerRemoved, the console is in the demo mode Contacts.Avoid moving your hands. When yourWhen you are finished exercising, remove Adjust the incline of the treadmill to the lowestSelect one of the preset workout programs HOW to USE Preset Workout ProgramsSelect a heart rate program HOW to USE Heart Rate ProgramsFollow your progress with the displays Put on the optional chest pulse sensorEnter your age and a maximum speed setting For the program HOW to Connect Your Portable Stereo HOW to Connect Your Computer HOW to Connect Your Home StereoVCR HOW to Connect Your VCRInsert the key into the console Press the Play button on your CD player orWhenkey. the program is completed, remove Return to the treadmill and stand on the foot HOW to USE Programs Directly from OUR WEB Site When the program has ended, remove the key Follow the on-line instructions to start ProgramOptional Chest Pulse Sensor Information MODE/DEMO ModeHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Problemsolution TroubleshootingDisplays of the console do not func- tion properly Walking belt is off-center or slips when walked onPlug the Power CORD. Next, remove Magnet and the Reed Switch is aboutExercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesQty Description R1103AUse the chart below to identify small parts during assembly HOW to Order Replacement PartsPart Identification Chart HRTL11940 Exploded DRAWING-Model No. HRTL11940 Limited Warranty
Top Page Image Contents