Healthrider H500i manual Troubleshooting, Problem The power turns off during use

Page 19

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If you need further assistance, please see the front cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 10). Use only a single-outlet surge suppres- sor that meets all of the specifications described on page 10. Important: The treadmill is not com- patible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c.Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes, and then press the switch back in.

c

Tripped

Reset

PROBLEM: The power turns off during use

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, see the front cover of this manual.

PROBLEM: The incline of the treadmill does not change correctly

SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re- move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system.

PROBLEM: The display of the console does not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. Remove the three hood Screws (7). Carefully pivot the Hood (41) off.

a

7

 

 

41

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model No. HRTL71706.0 Serial No QUESTIONS?Call TOLL-FREE Table of Contents Important Precautions Page Back Before YOU BeginFor your benefit, read this manual carefully before Right SideExtension leg. Firmly tighten the Extension Leg Bolts AssemblyShaft at least 6 long and wire cutters Make sure that the power cord is unpluggedFrame 58 yet Make sure that the ground wire see step Connect the connectors properly seeConnectors are not Connected Be careful to avoid pinching any of the wiresSmall Screws HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerTurn on the fan if desired Measure your heart rate if desiredWhenkey. you are finished exercising, remove Select one of the six cross trainer programs HOW to USE a Cross Trainer ProgramContinue the cross trainer program Perform the first strength exercise when PromptedOptional Chest Pulse Sensor Information MODE/DEMO ModeHOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Top View Exercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesQty Description R0408AOrdering Replacement Parts Exploded Drawing A-Model No. HRTL71706.0 R0408A Exploded Drawing B-Model No. HRTL71706.0 R0408A Exploded Drawing C-Model No. HRTL71706.0 R0408A Exploded Drawing D-Model No. HRTL71706.0 R0408A Limited Warranty
Related manuals
Manual 28 pages 21.51 Kb
Top Page Image Contents