Healthrider H500i manual Small Screws

Page 9

8.Hand tighten four additional Screws (3) into the Handrail (20) and the console assembly. Then, tighten all nine Screws used in step 7 and this step; do not overtighten the Screws.

9.Attach the Latch Housing (73) to the left Upright (84) with two Screws (3); start both Screws and then tighten them. Note: Make sure that the large hole in the Latch Housing is on the indicated side.

Remove the knob from the pin. Make sure that the collar and the spring are on the pin. (Note: If there are two collars, place one on each side of the spring.) Next, insert the pin into the Latch Housing (73). Then, tighten the knob onto the pin.

8

Console Assembly

 

3

3

20

3

9

 

 

84

 

73

Knob

 

Spring

 

3

 

Collar

 

Large Hole

 

Pin

10.Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the tread- mill. Note: Extra hardware may be included. Keep the included hex key in a secure place; the large hex key is used to adjust the walking belt (see page 20).

If you purchase the optional chest pulse sensor (see page 16), follow the steps below to install the receiver included with the chest pulse sensor.

1.Remove the key from the console and unplug the power cord.

Remove the Screw (3) and the Access Door (76) from the back of the Console Base (85).

2.Connect the wire on the receiver (A) to the indi- cated wire extending from the Console Base

(85). Hold the receiver so the small cylinder is oriented as shown and is facing the Console Base. Attach the receiver to the plastic posts on the Access Door (76) with the two included small screws.

3.Make sure that no wires are pinched. Reattach the Access Door (76) with the Screw (3). Discard the other wires included with the receiver.

85

Small Screws

Wire

A

Small

Cylinder

3

76

9

Image 9
Contents QUESTIONS? Model No. HRTL71706.0 Serial NoCall TOLL-FREE Table of Contents Important Precautions Page For your benefit, read this manual carefully before Before YOU BeginRight Side BackShaft at least 6 long and wire cutters AssemblyMake sure that the power cord is unplugged Extension leg. Firmly tighten the Extension Leg BoltsFrame 58 yet Connectors are not Connected Connect the connectors properly seeBe careful to avoid pinching any of the wires Make sure that the ground wire see stepSmall Screws Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerMeasure your heart rate if desired Turn on the fan if desiredWhenkey. you are finished exercising, remove Select one of the six cross trainer programs HOW to USE a Cross Trainer ProgramContinue the cross trainer program Perform the first strength exercise when PromptedOptional Chest Pulse Sensor Information MODE/DEMO ModeHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Top View Exercise Intensity Conditioning GuidelinesWorkout Guidelines Exercise FrequencyQty Description R0408AOrdering Replacement Parts Exploded Drawing A-Model No. HRTL71706.0 R0408A Exploded Drawing B-Model No. HRTL71706.0 R0408A Exploded Drawing C-Model No. HRTL71706.0 R0408A Exploded Drawing D-Model No. HRTL71706.0 R0408A Limited Warranty
Related manuals
Manual 28 pages 21.51 Kb