Healthrider H500i manual Assembly, Shaft at least 6 long and wire cutters

Page 6

ASSEMBLY

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill perfor- mance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included hex key

and your own phillips screwdriver

(with a

shaft at least 6" long) and wire cutters

.

 

Use the drawings below to identify the hardware used during assembly. Note: If a part is not in the parts bag, check to see if it has been preattached to one of the parts to be assembled. To avoid damaging plastic parts, do not use power tools for assembly.

Ground Screw

Screw (3)–11

 

(33)–1

 

2 1/4" Extension Leg Bolt (92)–2

 

 

 

Star Washer (8)–8

 

Front Endcap

 

 

Screw (14)–2

 

2 1/2" Extension Leg Bolt (65)–2

 

 

1" Tek Screw (83)–2

Extension Leg Nut (67)–2

Handrail Bolt (64)–4

1. Make sure that the power cord is unplugged.

1

 

 

 

With the help of a second person, carefully tip

 

 

the treadmill onto its left side as shown. Partially

84

14

fold the Frame (58) so the treadmill is more sta-

 

 

ble. Do not fully fold the Frame until the

 

44

treadmill is completely assembled.

 

 

 

Insert an Extension Leg (89) into the base of the

92

 

 

 

Uprights (84). Hold an Extension Leg Nut (67) in

8

 

the bottom of the Extension Leg, and thread a

 

 

 

2 1/4” Extension Leg Bolt (92) with a Star

 

8

Washer (8) into the top of the Extension Leg.

 

 

Next, thread a 2 1/2” Extension Leg Bolt (65) with

 

67

a Star Washer (8) into the bottom of the

89

Extension leg. Firmly tighten the Extension

 

65

Leg Bolts.

 

58

 

 

 

Slide a Front Endcap (44) onto the base of the

 

 

Uprights (84). Partially tighten a Front Endcap

 

 

Screw (14) into the Front Endcap and the base.

 

 

 

6

 

Image 6
Contents QUESTIONS? Model No. HRTL71706.0 Serial NoCall TOLL-FREE Table of Contents Important Precautions Page Right Side Before YOU BeginFor your benefit, read this manual carefully before BackMake sure that the power cord is unplugged AssemblyShaft at least 6 long and wire cutters Extension leg. Firmly tighten the Extension Leg BoltsFrame 58 yet Be careful to avoid pinching any of the wires Connect the connectors properly seeConnectors are not Connected Make sure that the ground wire see stepSmall Screws Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeMeasure your heart rate if desired Turn on the fan if desiredWhenkey. you are finished exercising, remove HOW to USE a Cross Trainer Program Select one of the six cross trainer programsPerform the first strength exercise when Prompted Continue the cross trainer programInformation MODE/DEMO Mode Optional Chest Pulse SensorHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Top View Workout Guidelines Conditioning GuidelinesExercise Intensity Exercise FrequencyR0408A Qty DescriptionOrdering Replacement Parts Exploded Drawing A-Model No. HRTL71706.0 R0408A Exploded Drawing B-Model No. HRTL71706.0 R0408A Exploded Drawing C-Model No. HRTL71706.0 R0408A Exploded Drawing D-Model No. HRTL71706.0 R0408A Limited Warranty
Related manuals
Manual 28 pages 21.51 Kb