Reebok Fitness RBE09950 manual

Page 5

2.

Orient the Rear Stabilizer (2) as shown. Attach the

2

 

 

 

Rear Stabilizer to the Frame (1) with four M8 x 65mm

 

 

 

 

 

 

 

Button Screws (95) and four M8 Split Washers (85).

 

 

 

 

 

 

2

 

 

 

1

 

 

 

 

 

85

 

 

 

85

95

 

 

 

 

 

 

 

95

 

 

3.

Slide an M8 x 25mm Washer (119) onto an M8 x

3

 

 

 

20mm Button Screw (118). Tighten the Button Screw

 

 

 

 

Opening

 

 

into one end of the Incline Axle (68). Apply a small

 

 

 

amount of the included grease to the Incline Axle.

5

 

 

 

 

 

 

 

Orient the Ramp (5) so that the opening is up as

 

 

 

 

shown. Fit the welded tube on the underside of the

 

Welded

 

 

Ramp between the two rings on the top of the Frame

 

Tube

 

 

(1). Insert the Incline Axle (68) through the rings and

 

119

118

 

the welded tube.

 

 

 

 

Grease

 

 

Slide an M8 x 25mm Washer (119) onto an M8 x

 

 

 

 

20mm Button Screw (118). Tighten the Button Screw

 

 

 

 

into the open end of the Incline Axle (68).

 

68

 

 

 

 

 

 

 

119

 

 

 

 

118

 

 

4. Using your fingers, turn the shaft on top of the Motor

4

 

 

 

(46) counterclockwise until it stops turning. Next, fit the

1

 

 

5

 

 

opening of the Ramp (5) over the front of the Frame

 

 

 

(1) as shown. Position the U-bracket on the underside

 

 

 

 

of the Ramp over the end of the shaft as shown.

 

111

 

 

 

 

 

 

Insert the Clevis Pin (112) through one side of the U-

 

65

 

 

bracket on the Ramp (5), an 8mm Plastic Spacer

112

 

 

 

 

 

(111), the shaft on the Motor (46), another 8mm Plastic

 

 

 

 

Spacer, and the other side of the U-bracket. Then,

 

46

 

 

insert the straight end of a Hairpin (65) through the

 

 

 

 

 

 

 

hole in the Clevis Pin.

 

 

 

5

Image 5
Contents Customer HOT Line Model No. RBE09950 Serial NoImportant Precautions Table of ContentsRight Side Before YOU BeginBack Assembly Page Top of the Frame, being careful not to pinch Wire HarnessesDo not pinch the wire harnesses during this step Page Page Elliptical Exerciser Operation HOW to Plug in the Power CordThis product must be grounded Exercising on the Elliptical ExerciserConsole Diagram Features of the Console HOW to USE the Manual Mode Cals Turn on the fans if desired HOW to USE a Preset Program Enter a maximum target heart rate setting HOW to USE a Heart Rate ProgramSelect one of the two heart rate programs Press the Start button to start the programAdjust the angle of the ramp as desired Select one of the two custom programs HOW to Create and USE a Custom ProgramHOW to Connect Your Portable Stereo HOW to Connect Your Home Stereo HOW to Connect Your Computer HOW to Connect Your VCR PressVCR. the play button on your CD player or Return to the elliptical exerciser and begin Pedaling HOW to USE Programs Directly from OUR WEB SiteFollow the on-line instructions to start Program Pulse Sensor Troubleshooting Maintenance and TroubleshootingHOW to Calibrate the Incline System HOW to Move the Elliptical ExerciserExercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencyQty Description Part LIST-MODEL NO. RBE09950Qty Description Exploded DRAWING-MODEL NO. RBE09950 Page Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty