Life Fitness Fit-1 manual Button Head

Page 15

STEP 18:

 

Slide two 5” ACCORIDIAN SLEEVES

36

 

(36) over the shafts on the PIVOT ARM

 

 

(9) as shown in FIGURE 18.

37

Slide two PILLOW BLOCKS (37) over

 

 

the shafts on the PIVOT ARM (9) as

 

 

shown in FIGURE 18.

 

 

 

9

 

 

FIGURE18

 

 

4

3/8 X 3” (76m) 72

BUTTON HEAD

74

 

 

 

35

37

 

9

 

 

75

78

 

3

76

73

FIGURE 19

STEP 19:

SECURELY assemble the PILLOW BLOCKS (37) on the PIVOT ARM (9) to the LEFT and RIGHT BOOM SUPPORTS (3 & 4) using four 3/8 X 3” BUTTON HEAD BOLTS (72), four BLACK 3/8” SAE WASHERS (74), four RH WASHERS (76), four 3/8” SAE WASHERS (75), four 3/8” LOW HEIGHT LOCK NUTS (73) and four RH CAPS (78) as shown in FIGURE 19.

IMPORTANT! When PIVOT ARM (9) is centered and level in the PILLOW BLOCKS (37), tighten the PILLOW BLOCK set screws.

Slide two 1-3/8” OD COVER CAPS (35) over the ends of the shaft on the PIVOT ARM (9) as shown in FIGURE 19.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0

 

 

 

 

1/2

 

 

 

 

 

 

1

 

 

 

 

 

1/2

 

 

 

2

 

 

 

 

 

 

 

 

 

1/2

3

 

 

 

 

1/2

 

 

 

4

 

 

 

 

 

 

 

 

 

1/2

5

 

 

 

 

 

1/2

 

 

 

 

6

 

 

 

 

10

 

 

 

 

 

 

 

20

30

 

40

 

 

 

50

 

 

 

 

 

 

60

 

 

 

 

70

 

 

 

 

 

 

 

80

 

90

 

 

 

 

100

 

 

 

 

 

 

110

 

 

 

 

 

120

 

 

 

 

 

 

130

 

140

 

 

 

 

150

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

15

Image 15
Contents FIT Series FIT-1 Parts List Height Lock NUT Tools Required for Assembly Step 73m X 2-1/2 67m X 3-1/2 90m 60 3/8 X 1 25m Spring PIN Tighten X 4-1/4 106m Step 67 3/8 X 4-1/4 106m 69 3/8 X 6-1/2 164m Black 53 3/8 X 97m Button Head X 2-1/2 67m Step 100 110 120 130 140 150 X 3/4 X 2-3/4 70m X 1-3/4 62 3/8 X 1-3/4 43m Step 62 3/8 X 1-3/4 43m X 3-3/4 93m Step Serial # Warranty Information