INTRODUCTION
IMPORTANT PRECAUTIONS
ASSEMBLY
BEFORE YOU BEGIN
CONDITIONING GUIDELINES
CABLE “D” | CABLE “A” | |
| UPPER PULLEY ASSEMBLY | |
LAT BAR BRACKET ASSEMBLY |
| |
LAT PULLDOWN BAR | DUAL FLOATING PULLEY BRACKET | |
SINGLE FLOATING PULLEY BRACKET | ||
| ||
COVER SET |
| |
CENTER SUPPORT FRAME | WEIGHT SHIELD | |
CABLE “C” |
| |
MAIN SUPPORT FRAME (RIGHT) | GUIDE ROD | |
| ||
HANDLE | RADIAL ARM ASSEMBLY | |
| ||
RADIAL ARM ADJUSTMENT PIN | MAIN SUPPORT FRAME (LEFT) | |
SEAT BACK PAD | WEIGHT SELECTION PIN | |
SEAT BOTTOM PAD | ||
| ||
| SINGLE FLOATING PULLEY BRACKET | |
SEAT WELDMENT SET | SEAT SET SAFETY PIN | |
| ||
SEAT HEIGHT ADJUSTMENT KNOB |
| |
LEG EXTENSION/ |
| |
CURL DOWN TUBE |
| |
FOAM ROLLERS | BASE FRAME | |
ADJUSTABLE FOOTPLATE | CABLE “B” | |
TOOLS INCLUDED |
| |
Screwdriver | 4 mm Allen Wrench | |
19 mm Flat Wrench | 6 mm Allen Wrench | |
13 mm/17 mm Flat Wrench | 8 mm Allen Wrench |
PARTS INCLUDED
PRE - ASSEMBLY
note: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before
completely tightening any ONE bolt. NOTE: A light application of grease may aid in the installation of hardware. Any grease, such as lithium bike grease is recommended.
A S S E M B LY STEP 1 |
|
|
| |
| MAIN SUPPORT | A | Place base frame on floor in | |
|
| desired location. | ||
| FRAME (RIGHT) |
| ||
|
|
| ||
|
| B | Remove 6 NYLON NUTS (C) | |
|
|
| and 6 FLAT WASHERS (B) from | |
|
|
| BASE FRAME. | |
|
| C | Attach right MAIN SUPPORT | |
|
|
| FRAME to right side of base | |
| MAIN SUPPORT |
| frame using 2 flat washers | |
|
| (B) and 2 NYLON nuts (C). | ||
| FRAME (LEFT) |
| ||
CENTER SUPPORT |
| D | Repeat on other side. | |
NYLON NUT (C) |
|
| ||
FRAME | E | Attach center SUPPORT | ||
| ||||
| FLAT WASHER (B) |
| FRAME to BASE frame using | |
|
|
| 2 flat washers (B) and 2 | |
|
|
| NYLON nuts (C). |
INTRODUCTION
IMPORTANT PRECAUTIONS
ASSEMBLY
BEFORE YOU BEGIN
CONDITIONING GUIDELINES
TROUBLESHOOTING & MAINTENANCE
1 Seat Set Safety Pin
2 Foam Rollers
1 Seat Back Pad
1 Seat Bottom Pad
1 Main Base Frame
1 Main Support Frame (Right)
1 Main Support Frame (Left)
1 Radial Arm Assembly
1 Nylon Ankle Strap
1 | Center Support Frame | 1 | Dual Floating Pulley Bracket |
2 | Handles | 1 | Front Cover |
1 | Leg Extension/Curl Down Tube | 1 | Back Cover |
1 | Seat Weldmen Set | 2 Single Floating Pulley Brackets | |
2 | Weight Shields | 1 | Upper Pulley Assembly |
2 | Guide Rods | 1 | Lat Bar Bracket Assembly |
1 | Weight Selection Pin | 4 | Cables |
1 | Upper Pulley Assembly | 9 | Hardware Bags |
1 | Lat Pulldown Bar |
|
|
BASE FRAME |
TROUBLESHOOTING & MAINTENANCE
LIMITED WARRANTY
If you have questions or if there are any missing parts, contact
Further contact information is located on the back cover of this manual.
For a complete exploded diagram, see Quick Start and Parts Guide (included in User’s Guide bag). |
| |
|
| |
|
|
|
LIMITED WARRANTY
SXS_5.7_rev.1.1.indd | 8/30/07 11:12:39 AM |