INTRODUCTION
A S S E M B LY STEP 6
HARDWARE BAG 5 CONTENTS :
BOLT (I) | FLAT WASHER (J) | NYLON NUT (K) | BUMPER |
Qty: 4 | Qty: 8 | Qty: 4 | Qty: 2 |
A S S E M B LY STEP 7
HARDWARE BAG 6 CONTENTS : |
| A | Open HARDWARE BAG 6. | |
CABLE A | CABLE B | B | Remove nylon nut and threaded | |
Qty: 1 | Qty: 1 | |||
| screw from end of CABLE A. | |||
|
|
|
INTRODUCTION
IMPORTANT
PRECAUTIONS
ASSEMBLY
BEFORE
YOU BEGIN
CONDITIONING TROUBLESHOOTING
GUIDELINES& MAINTENANCE
WARRANTY |
| |
LIMITED |
| |
12 | ||
| ||
|
|
| FLAT WASHER (J) |
|
| BOLT (I) |
|
FLAT WASHER (J) |
|
|
NYLON NUT (K) |
|
|
UPPER PULLEY |
|
|
ASSEMBLY |
|
|
|
| GUIDE ROD |
| SELECTOR PIN | BAYONET |
|
| |
|
| TOP WEIGHT PLATE |
|
| WEIGHT PLATES |
|
| BUMPER |
FLAT WASHER (J) |
|
|
NYLON NUT (K) |
| BOLT (I) |
|
| FLAT WASHER (J) |
| BASE FRAME | |
AOpen HARDWARE BAG 5.
BInstall 2 BOLTS (I), 4 FLAT WASHERS (J) and 2 NYLON NUTS (K) into the BASE FRAME as shown in diagram.
CInsert each GUIDE ROD into the BASE FRAME as shown in diagram.
DInstall rubber BUMPER onto each GUIDE ROD.
EInstall each WEIGHT PLATE onto GUIDE RODS
NOTE: Ensure that each WEIGHT PLATE’s selector pin slot faces downward.
FInsert each GUIDE ROD into the corresponding hole in the UPPER PULLEY ASSEMBLY.
GSecure GUIDE RODS in UPPER PULLEY ASSEMBLY using 2 BOLTS (I), 4 FLAT WASHERS (J) and 2 NYLON NUTS (K).
NOTE: Ensure that each bolt is inserted through the hole at the top of the GUIDE ROD.
HTighten all hardware.
CABLE A |
|
SINGLE FLOATING |
|
PULLEY BRACKET |
|
| CABLE A |
SINGLE FLOATING |
|
PULLEY BRACKET |
|
DUAL FLOATING |
|
PULLEY BRACKET |
|
CABLE B |
|
LEG EXTENSION/ |
|
CURL ARM CABLE |
|
CABLE A |
|
SCREW AND NUT | TOP WEIGHT |
| |
| PLATE |
CInsert cable end into LAT BAR BRACKET ASSEMBLY pulley as shown in diagram.
NOTE: After passing through first pulley bracket, thread cable through DUAL FLOATING PULLEY BRACKET then thread back into LAT BAR BRACKET ASSEMBLY.
D
EScrew the other end of CABLE A into SINGLE FLOATING PULLEY.
FRemove nylon nut and threaded screw from end of CABLE B.
GInsert cable end into BASE FRAME pulleys as shown in diagram.
NOTE: After passing through first pulley bracket, thread cable through DUAL FLOATING PULLEY BRACKET.
HAfter CABLE B routing is complete replace threaded end and nut onto cable end, and install SINGLE FLOATING PULLEY.
IAttach CABLE B to LEG EXTENSION/CURL ARM CABLE.
PRECAUTIONS
IMPORTANT
ASSEMBLY
YOU BEGIN
BEFORE
GUIDELINES
CONDITIONING
TROUBLESHOOTING & MAINTENANCE
| WARRANTY | |
| LIMITED | |
13 | ||
| ||
|
|
SXS_5.7_rev.1.1.indd | 8/30/07 11:12:54 AM |