Image IMBE53900 manual Tighten all of the Locknuts used in steps 1 to

Page 10

12.Attach the upper end of one of the Weight Guides (53) to the bracket on the Upright (43) with an M8 x 30mm Bolt (64) and an M8 Washer (77).

Attach the other Weight Guide (53) to the other Upright (43) in the same manner.

Tighten all of the Locknuts used in steps 1 to 12.

13.Press a 50mm x 70mm Outer Cap (10) onto each end of the Stabilizer (13).

Attach the Stabilizer (13) to the Bench Frame (5) with two M10 x 60mm Button Head Bolts (12) and two M10 Nylon Locknuts (11). Note: There is an indentation around each hole on one side of the Stabilizer; this side must be facing the floor so that the warning decal is in the position shown.

Note: Do not tighten the Nylon Locknuts yet.

14.Press a 50mm Square Outer Cap (20) onto each end of the Bench Base (7).

Attach the Bench Base Joint Plate (19) to the Bench Base (7) with two M10 x 70mm Bolts (21), two M10 Washers (6), and two M10 Nylon Locknuts (11).

Attach the Bench Leg (1) to the Bench Base Joint Plate (19) with two M10 x 70mm Bolts (21), two M10 Washers (6), and two M10 Nylon Locknuts (11).

Be sure the welded nut is in the position shown. Note: Do not tighten the Nylon Locknuts yet.

15.Attach the Bench Leg (1) to the Bench Frame (5) with two Bench Joint Plates (18), four M10 x 70mm Bolts (21), and four M10 Nylon Locknuts (11).

Note: Tighten all the M10 Nylon Locknuts (11) used in steps 13-15.

12

 

 

 

64

 

 

 

 

 

 

 

 

77

 

 

53

 

43

 

 

 

 

13

 

 

 

11

 

 

 

 

 

 

 

 

13

 

5

10

 

Decal

 

 

 

 

 

 

 

12

 

 

 

 

10

14

 

 

 

Welded Nut

 

 

 

6

1

 

 

 

 

 

21

 

 

11

 

7

 

6

 

 

 

20

6

 

 

19

 

21

 

6

 

 

 

 

 

 

 

 

20

 

15

21

 

 

 

 

 

18

 

 

 

 

 

 

 

 

 

5

 

 

 

 

18

 

 

 

1

11

 

 

 

 

10

Image 10
Contents Customer HOT Line Model No. IMBE53900 Serial NoMon.ÐFri., 6 a.m.Ð6 p.m. MST Table of Contents Important Precautions DecalRight Side Before You BeginLeft Side Part Identification ChartÑModel No. IMBE53900 R1100A Assembly Some small parts may be pre-assembledPage Pull-up Bar Round tube Guide away from the Upright 43 as you insert it Locknut yetTighten all of the Locknuts used in steps 1 to Locknut 11. Note Do not over tighten the Nylon Adjustment Bracket must pivot easilyOver tighten the Nylon Locknut the Seat Locknut the Seat Mounting Bracket must pivotM10 Nylon Locknut the Leg Lever must pivot easily Using the Locking BAR and Safety Spotters Adjusting the Weight BenchUsing the Safety Spotters Using the Curl PAD Adjusting the PAD TubesUsing Olympic Weights on the LEG Lever Adjusting the Seat Adjusting the BackrestLimited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT Remove this Part LIST/EXPLODED Drawing From the Manual Part ListÑModel No. IMBE53900 Qty DescriptionExploded DrawingÑModel No. IMBE53900