Assembly, Attaching the pedals | Cateye EC-L32OO guide

Assembly

Assemble the unit according to the following procedure. Learn how to adjust each part as well.

* In addition to the tools provided, please prepare a screw driver.

1. Attaching the leg pipes

4. Mounting the saddle

• Remove the two screws from each leg pipe.

• Lift up the seat post to a proper height for

• Place the front leg pipe under the front end of

saddle mounting.

the main body as Fig. 1 and fasten it with the

• Mount the saddle at the top of the seat

screws securely.

post as Fig. 5.

#13 Wrench

Nut

• Place the rear leg pipe under the rear end of

• Adjust the saddle angle to make it horizon-

Fig. 1

the main body as Fig. 2 and fasten it equally.

tal, and use the #13 end of the spanner

Front

CAUTION: Place the leg pipes with the "TOP"

wrenches to tighten the nuts from both

Seat post

mark facing upward.

sides.

Pipe with casters

TOP mark

ADJUSTMENT: Turn the level adjusters if nec-

Fig. 5

essary, in order to compensate the

5. Attaching the pedals

floor unevenness.

#15 Wrench

REFERENCE: When the marking line is at the

• Attach the pedals to the crank as Fig. 6

top, the rear leg is at the same level

and fasten them firmly using the #15 end

Crank

as front.

of the wrench provided.

• Be sure to identify R and L of the pedal

Rear leg pipe

with the engraved mark.

Marking line

• Fasten clockwise the R pedal, and coun-

terclockwise the L pedal. (Fig. 7)

Fig. 6

Level adjusters

Fig. 2

Rear

Left(L)

Front

Right(R)

Belleville

2. Mounting the handle post

spring

•

Attach handlebar post to base post and secure with fastening

Fig. 7

Handlebar post

screws.

6. Mounting the handlebar and

Handlebar clamp bracket

Base post

3. Seat post position

adjusting the handlebar grip

Handlebar

(ADJUSTMENT)

Quick release lever

(ADJUSTMENT)

post

Assembly completed.

• Place the Handlebar clamp bracket and

Washers

fastening

Seat post

•

Turn the seat post knob clockwise and coun-

Pitch 1" (approx. 25 mm)

screw

(Control Unit already mounted)

the handle bar into place. (fig 8)

terclockwise and pulling it allows the seat

• Place both washers provided onto the Quick

post to slide up and down.(Fig.4)

Seat post knob

release and screw it into the handlebar clamp

• Adjust the seat post to an appropriate height

assembly until there is a loose fit. The Quick

and release the seat post knob, and move

Loosen

release works like a clamp, test it to determine

the seat post slightly up or down.

Pull

when it is open (clamp assembly will be

• The spring inside the seat post knob drives

Tighten

loose). Test for proper tightness using the le-

Handleber

the pin into the nearest hole on the seat post

Fig. 8

ver action to close the Quick Release. If at

and turn it clockwise until the seat post can-

this time the handle bar is too loose open the

Tighten

not wobble.

Quick Release lever and turn the screw por-

(Lay down)

•

The pitch of the seat post hole is 1 inch

tion into the Handlebar clamp bracket 1 to 2

(approx.25mm).

turns. Repeat the Test process until the

Fig. 3

CAUTION: Confirm that the pin of the seat

handle bar is held tightly into place when the

post knob must be in the hole

lever is closed and loose enough to adjust the

securely.

bar when the lever is open.

CAUTION: Do not pull the seat post knob

Loosen (Raise)

Fig. 4

REFERENCE: Be sure that when you close

while mounted. The seat post

the Quick Release lever it

Turn the quick relaese lever

may drop down suddenly.

snaps firmly into place.

for adjustment

4	5	EC-L32OO