Cateye CC-MT400 owner manual Computer Operations, Measurement Display, Power Saving Screen

Computer Operations

Selection of the data-display mode (bottom of the screen).

Pressing the MODE button changes the functions in the sub-display.

Clock Time - In Elapsed Time, press and hold the Mode button for two seconds to display Clock Time. Pressing the Mode button again will return the sub-display to Elapsed Time.

Trip Distance 1 and 2 – The computer has two separate trip distances. Trip Distance 2 is reset independently. It can be used to record distance within a ride or multiple days distances. In Trip Distance 1, press and hold the Mode button to select Distance 2. You will continue to view this distance until you select Distance 1 with the same procedure.

Measurement Display

Speed 0.0 (4.0) - 105.9 km/h [0.0 (3.0) - 65.9 mph]

	Average Pace Arrow
	It shows that the current speed is faster
	or slower than the Average Speed.
	Faster	Slower
	Auto-mode Icon
	When it is lit, the measurements
Wheel Icon	are automatically started or stopped.

Power Saving Screen

(When no signal is received for about one hour, the computer switches to the power-saving mode)

When you push either of the MODE button or the START/STOP button or you ride the bicycle, the display comes back to the measurement display.

Start or Stop of Measurements.

The computer can be programmed to run in either MANUAL MODE or AUTO TIME MODE. In Manual Mode you must press the START / STOP button to turn on and off the Timer, which records Distance and Average

Speeds. In Auto Time the computer turns the Timer on and off de- pending on a signal from the sensor.

When speed is detected by the computer and the Timer is running, the km/h or mph will flash. Speed will appear on the computer screen and the Odometer will record, regardless if the Timer is running or not.

• Auto Time Mode (Automatic Measurement)

In AUTO TIME mode, the letters will appear on the computer screen. Elapsed time, Average and Distance are recorded automatically and the Timer, stops when the speed stops. In this mode the START/STOP button is not operable.

• Manual Measurements

When you don’t see the icon on the screen, you can start or stop the measurements by pushing the START/STOP button.

Measurement Unit Icon

Indicates which wheel setting is selected.

Mode Selection Illustrations (bottom of the screen)

Av

Average Speed

0.0 -105.9 km/h

[0.0 - 65.9 mph]

Dst

Trip distance - 1

0.00 -999.99 km [mile]

Trip distance - 2

0.00 - 999.99 km

MODE [mile]

You can program two tire sizes and use either of them.

Road MTB

How to select tire size			or
		When data other than Odo is
		displayed	SET
		Keep on pressing the
		button for two seconds
		When the Odo data is
		displayed
		MODE	ST/STOP
Road	MTB
		Keep on pressing buttons
		for 2 sec. at the same time
Inputting the Tire

When you push the button, measurements of Elapsed Time, Average Speed, Trip Distance 1 and 2 are started and they are stopped with the second push of the button.

• How to set ON or OFF the auto-mode

Push the SET button on the back side of the computer while Elapsed Time, Average Speed, Trip Distance 1 or 2 is displayed, then the icon is lit” (ON) or turned OFF.

Resetting Elapsed Time, Trip Distance, Average Speed and Max Speed.

Press and hold the MODE and START/STOP buttons for 2 sec. in either the Elapsed Time, Trip Distance 1, Average Speed or Maximum Speed functions to reset these functions. The Odometer and Trip Distance 2 are not reset. See below for details.

• Resetting Trip Distance 2

	ST/STOP
SET	Tm
	Av
	Dst

MODE

MODE

* Resetting of Dst2 only

Odo

Odometer

0.0 - 99999 km [mile]

Mx

Maximum Speed

0.0 (4.0) - 105.0 km/h [0.0(3.0) - 65.0 mph]

Circumference	Range of setting:
	100 - 300 cm
Return to Odo	SET
SET
When the measurements
are stopped
Increase	Decrease
the number	the number

MODEST/STOP

Trip Distance 2 is reset independently. When Trip Distance 2 is on the screen, press and hold both the MODE and START/STOP buttons to re- set.

Computer Functions

• Power-saving Function

ST/STOP

For 2 sec. at the same time

Tm		Setting The Clock Time
Elapsed Time		24 hour or 12 hour system is to
		be used with km/h or mph unit respectively
0:00’00” - 9:59’59”
For 2 sec.	Return to Clock display		Increase the number
		SET	MODE

When no signal has been received for about one hour, the computer goes into the power savings mode to only display the Clock. When any button is pushed or the wheel is rotated, the computer screen reappears.

• Dual Tire Size

You can program two, and , tire circumferences and can easily switch to or vise versa to enable the system to be used by two bicycles which have different tire sizes. The com-

puter program for circumference is programmed for low speed use. We recommend to use this for MTB's.

• Moving Elapsed Time, Average Speed and Maximum	Elapsed	Average	Maximum
	Time	Speed	Speed
Speed to the upper display.
	Minute	Av	Mx	Upper
You can move the Elapsed Time, Average and Max Speed	Second			Part
displays to the upper display for easier viewing. Hold the	Hour	SPD	SPD	Lower
				Part
START/STOP button for 2 sec. and the sub-display will ap-
pear in the upper display. Hold the START/STOP button
again for 2 sec. and the display returns to the normal set up.
		ST/STOP
Troubleshooting

No display appears.

Is the battery dead?

Replace it by the new one and do all clear procedure.

Strange data appears

Do all clear procedure (write down the number of Odometer if possible before doing the all clear procedure and input it manually after choosing the measurement unit).

Measurements do not start when the START/STOP button is pushed.

Is the icon ON?

Turn the Auto-Mode off to enable the start or stop of the measurements by manual opera- tion of the button.

No speed data is displayed.

(If the speed data is not displayed, have the contact points short-circuited by a metal plate. In the case that this short-circuiting is detected by the computer, the computer is considered normal and the bracket and sensor may possibly have the cause of trouble.)

Is the gap between the sensor and the magnet too big? (should be within 5 mm) Does the marked line of the sensor align with the center of the magnet?

Adjust the position of the magnet and the sensor.

Make sure that the contact points of the bracket or of the main body are free from dirt. Wipe the contact points clean.

Is the cord not broken? Even if the outside of the cord looks normal, a breakage in the wire can occur. Replace the bracket and sensor set with a new one.

Maintenance

•To clean the computer or the attached parts, use diluted neutral detergent on a soft cloth, and wipe it off with a dry cloth.

Replacing The Battery	Close
When the display gets dim, replace the battery. If you want to retain and	Open
use the current reading of odometer, write down the odometer data before
replacing the battery.
• Put a lithium battery CR2032 in the computer with the (+) mark facing up.
• After replacing the battery, do the necessary set-up of the computer in
accordance with "Computer Set-up".

MODE	MODE
	Clock		SET
	0:00 - 23:59					ST/STOP
	[1:00 - 12:59]
		When the measurements
		are stopped.			Set the hour		Set the minute
Specifications
Battery Life : ---------------------------------		A Lithium Battery (CR2032), Approx:3 yrs
		(approx:1 hrs per day usage)
Control System : ----------------------------		4-bit 1-chip micro-computer (with a crystal oscillator)
Display : --------------------------------------		Liquid crystal display
Sensing System : ---------------------------		No-contact magnetic sensor
Range of Tire Circumference : -------------		100 cm – 300 cm (Initial value – A:210 cm					B:205 cm)
Range of Operational Temperature : ------		0°C – 40°C		[32°F – 104°F]
Dimension and Weight(Computer) : ------		38 x 54 x 17.5 mm [1-1/2 x 2-1/8 x 11/16"] / 28 g [1.0 oz]

*The factory-loaded battery life might be shorter than the above-mentioned specification.

*The specifications and design are subject to change without notice.

Limited Warranty

2-Year Warranty : Computer Head Only (excluding the attached parts and deteriorated battery )

If any trouble or damage occurs during normal use, the product computer will be repaired or replaced free of charge. Type your name, address, telephone number or e-mail address, date of purchase and the situation of trouble and send it back together with the product to the closest address below. Trans- portation charges shall be borne by the customer. After being repaired, the product will be shipped back to the customer.

CO.,LTD. 2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan Attn.: CAT EYE Customer Service Section

Service & Research Address for United States Consumers:

CAT EYE Service & Research Center

1705 14th St. 115 Boulder, CO 80302

Phone: 303-443-4595	Toll Free: 800-5CATEYE
Fax: 303-473-0006	e-mail: service@cateye.com
* Accessory parts are available for the customers as shown below.	URL: http://www.cateye.com

Parts	#169-9300 [169-9305]	#169-9755	#169-9691
	Bracket Sensor Kit [Long]		Wheel Magnet
Standard		Attachment Kit	#166-5150
			Lithium Battery (CR2032)

	#169-9350	#169-9302
	Heavy Duty Wire and Bracket	[#169-9307]
	Sensor Kit	Center Mount Bracket
Parts		Kit [Long]
		#169-9303
		Bracket Sensor Kit for Aero Bar
Optional
		#169-9760
	#169-9304	Magnet for
		Composite Wheel
	Stem Mount Bracket Kit