Power | Bay Technical Associates DS2-RPC, DS4-RPC, DS73 guide

DS-RPC OWNER’S MANUAL INSTALLATION

__________________________________________________________________________________________

PREPARING THE INSTALLATION SITE

The installation area should be clean and free of extreme temperatures and humidity. Allow sufficient space behind the unit for cabling.

POWER

CAUTION: This unit is intended for indoor use only. Do not install near water or expose this unit to moisture. To prevent heat buildup, do not coil the power cord when in use. Do not use extension cords. Do not attempt to make any internal changes to the power source. Do not attempt to modify any portion or component of a DS-RPC unit unless specifically directed to. BayTech must perform any internal changes.

CAUTION: High-voltage surges and spikes can damage this equipment. To protect from such power surges and spikes, this unit must have a good earth ground. A grounding screw connection is located near the power switch on the back of the unit.

CAUTION : Before removing or replacing any modules, turn off main power switch located on the DS-RPC unit. Communication to the DS-RPC will be disrupted while power is off.

CAUTION: Before removing or replacing any cables or power cords, turn off main power switch located on the DS-RPC. Communication to the unit will be disrupted while power is off.

CAUTION: Do not exceed the AC current rating for the selected model. (See Appendix A “SPECIFICATIONS” for the DS-RPC).

CAUTION: Although the power switch is turned OFF, the unit is not totally isolated from the power supply. In order to be absolutely removed from the power supply, the power cord must be unplugged from the unit.

11

Image 19

Bay Technical Associates DS2-RPC, DS4-RPC, DS73, DS2-RPC DS4-RPC owner manual Preparing the Installation Site, Power

Contents

BayTech Manual Publication #U140A124-01 August DS-RPC Data SWITCH/POWER ControlPage Iii Page Introduction to the DS-RPC DS71-MD2 Technical Support Page Introduction to the DS-RPC Page Feature Description Action Programmable Features of the DS ModulesDS71 or DS71-MD2 Host Module Feature Description Action DS71-MD2 Host Module Programmable Features of the DS Modules con’t Module Feature Description Action DS73TP N Etwork EIA-232 Serial Connection DS-RPC Quick StartOperation Selecting a Device DS-RPC Module Configuration RPC Unpacking Installation Power Preparing the Installation Site Power UP Sequence Power ON/OFF StateCircuit Breaker RJ-45 Cables and Adapters CablingDS73TP Connection DS71 EIA-232 RJ-45 Pin/Signal Definition DS74 EIA-232 RJ-45 Pin/Signal Definition Modem Connections PIN Connection Detailed Operation ConfigurationConnecting to the DS-RPC EIA-232 Serial DS71-MD2 only Detailed Operation and Configuration Operation Device a Device B Device C Device D String Menu DrivenSelection Ascii Character Mode Binary Mode$BT2,1cr$BTBcr Terminate Binary Menu PPP DIAL-UP Configuration Status Or this for the DS71-MD2 Serial Port Configuration DTR RTS 115.2K None Off High Exit/Save..….......1 Selecting #1 will give the same results as Cr. New configuration changes are storedIf you have made necessary changes to Host device, type Y for yes, followed by For For 57.6K a for 76.8K B for 115.2K Enter Request For DTR RTS Host Code is $BT User programmable. Default Port SelectPort Select Code Character Guard is disabled Connect Port Default Connect Port ID Echo is disabledID Echo Header is enabled Login SetupHeader Default Password is BTA, disabled. Password Menu Auto Connect Port If enabled, the following header and menu appears Serial connection Port is disabled Escape Character ........… Rings to Answer is DisabledRings to Answer Minutes TimeoutDefault Connectivity Timeout is Connectivity 2B Hex or a plus sign + Default Escape Character is 43, which isEscape Character Or DS71-MD2 Identifies the unit. Default Unit ID is DS71Unit Reset Unit ID Ascii Driven Port Device Name …..............................3 Selections 1-8 are fully programmable DS73TP Enter password Dial-UP Default Subnet Mask is Default Dial-Up IP Address isSubnet Mask DNS Default Gateway address isGateway Primary 0.0 Default Primary DNS address isMenu. Default Secondary DNS address is Secondary Default Secondary Nbns address is Default Primary Nbns address isNbns Default Password is BTA Default User Name is user1User Name Module Default Module Name is DS73TPName RPC Operation Accessing Main Menu Controlling Receptacles Outlet 1, Outlet 2, Outlet 3, Outlet DS-RPC Config Change Password Outlet Outlet 4 Enter Request Is Enabled Enable/DisableConfirmation RPC Technical Support OUTLET3 Outlet DS-RPC Model DS-RPC Serial NumberModule Outlet REPACKAGING, Shipping and Returning to the Factory Call BayTech to get a Return Authorization Number FCC Requirements for the DS71-MD2 FCC Radio Frequency Interface Statement FCC Radio Frequency Interface Statement Appendix a SpecificationsTable A.1 Base DS71 Host DS71-MD2 DS74 Appendix B Save modem’s configuration in non-volatile memory Rockwell Chip SET Modems Command Interpretation MY Computer Appendix CMake NEW Connection DIAL-UP Networking Properties Post Dial Terminal Screen DS71 Mechanical Layout Appendix D Drawings DS71-MD2 Mechanical Layout DS74 Mechanical Layout DS73 Mechanical Layout Ascii Character Definition Appendix E Break condition · Rings to Answer · 45, 46 RTS/DTR Line Driver · 29, 31 XON/XOFF ·