Bay Technical Associates DS2-RPC, DS4-RPC, DS73, DS2-RPC DS4-RPC

DS-RPC OWNER’S MANUAL CABLING

__________________________________________________________________________________________

Tables 2 and 3 define the pin layout for the DS71 or DS71-MD2 and DS74.

		DS71 EIA-232 RJ-45 Pin/Signal Definition

Pin	EIA-232	Description
	Signal

1	Handshake	(DTR) Line Driver Inactive State = High: +12V when power is
	Out	applied. Used as a handshake line to enable/disable the receiving of
		characters.

2	Gnd	Signal ground

3	Handshake	(RTS) Line Driver Inactive State = High: +12 V when power is
	Out	applied. Not used to enable/disable.

4	TX Out	Transmit Data (data out)

5	RX In	Receive Data (data in)

6	Handshake	(DSR) Handshake In. –12V when not used.
	In

7	Gnd or	Signal ground when Jumper JP6-2 is connected to JP6-3. In order
	DCD In	for the DS71 to take advantage of “DCD Logon/Logoff” and “Auto
		Connect Port”, Jumper JP6-2 is connected to JP6-1 providing DCD
		In.

8	Handshake	(CTS) Used as a handshake line to enable/disable the receiving of
	In	characters.

Table 2 DS71 PIN SIGNAL DEFINITION

14

Image 22

Bay Technical Associates DS2-RPC, DS4-RPC, DS73, DS2-RPC DS4-RPC owner manual DS71 EIA-232 RJ-45 Pin/Signal Definition

Contents

DS-RPC Data SWITCH/POWER Control BayTech Manual Publication #U140A124-01 AugustPage Iii Page Introduction to the DS-RPC DS71-MD2 Technical Support Page Introduction to the DS-RPC Page Feature Description Action Programmable Features of the DS ModulesDS71 or DS71-MD2 Host Module Programmable Features of the DS Modules con’t Feature Description Action DS71-MD2 Host Module Feature Description Action DS73TP N Etwork Module EIA-232 Serial Connection DS-RPC Quick StartOperation Selecting a Device DS-RPC Module Configuration RPC Installation Unpacking Preparing the Installation Site Power Power UP Sequence Power ON/OFF StateCircuit Breaker RJ-45 Cables and Adapters CablingDS73TP Connection DS71 EIA-232 RJ-45 Pin/Signal Definition DS74 EIA-232 RJ-45 Pin/Signal Definition Modem Connections PIN EIA-232 Serial Detailed Operation ConfigurationConnecting to the DS-RPC Connection DS71-MD2 only Detailed Operation and Configuration Operation Device a Device B Device C Device D Ascii Character Menu DrivenSelection String Terminate Binary Binary Mode$BT2,1cr$BTBcr Mode PPP DIAL-UP Menu Configuration Or this for the DS71-MD2 Status Configuration Serial Port DTR RTS 115.2K None Off High Exit/Save..….......1 Host device, type Y for yes, followed by Cr. New configuration changes are storedIf you have made necessary changes to Selecting #1 will give the same results as For For 57.6K a for 76.8K B for 115.2K Enter Request For DTR RTS Host Code User programmable. Default Port SelectPort Select Code is $BT Character Guard is disabled Connect Port Default Connect Port ID Echo is disabledID Echo Header is enabled Login SetupHeader Password Default Password is BTA, disabled. Menu If enabled, the following header and menu appears Auto Connect Port Serial connection Port is disabled Escape Character ........… Answer DisabledRings to Rings to Answer is Connectivity TimeoutDefault Connectivity Timeout is Minutes Character Default Escape Character is 43, which isEscape 2B Hex or a plus sign + Unit ID Identifies the unit. Default Unit ID is DS71Unit Reset Or DS71-MD2 Driven Ascii Port Device Name …..............................3 Selections 1-8 are fully programmable DS73TP Enter password Dial-UP Default Subnet Mask is Default Dial-Up IP Address isSubnet Mask Primary Default Gateway address isGateway DNS Secondary Default Primary DNS address isMenu. Default Secondary DNS address is 0.0 Default Secondary Nbns address is Default Primary Nbns address isNbns Default Password is BTA Default User Name is user1User Name Module Default Module Name is DS73TPName Accessing Main Menu RPC Operation Controlling Receptacles Outlet 1, Outlet 2, Outlet 3, Outlet Change Password DS-RPC Config Outlet Outlet 4 Enter Request Is Enabled Enable/DisableConfirmation RPC Technical Support Outlet DS-RPC Model DS-RPC Serial NumberModule OUTLET3 Outlet Call BayTech to get a Return Authorization Number REPACKAGING, Shipping and Returning to the Factory FCC Radio Frequency Interface Statement FCC Requirements for the DS71-MD2 FCC Radio Frequency Interface Statement Appendix a SpecificationsTable A.1 Base DS71 Host DS71-MD2 DS74 Appendix B Rockwell Chip SET Modems Command Interpretation Save modem’s configuration in non-volatile memory MY Computer Appendix CMake NEW Connection Properties DIAL-UP Networking Post Dial Terminal Screen Appendix D Drawings DS71 Mechanical Layout DS71-MD2 Mechanical Layout DS74 Mechanical Layout DS73 Mechanical Layout Appendix E Ascii Character Definition Break condition · Rings to Answer · 45, 46 RTS/DTR Line Driver · 29, 31 XON/XOFF ·