Bay Technical Associates DS2-RPC, DS4-RPC, DS73, DS2-RPC DS4-RPC

DS-RPC OWNER’S MANUAL

DETAILED OPERATION AND CONFIGURATION

__________________________________________________________________________________________

NOTE: DTR is unchangeable when configuring the serial port. When configuring the Host Modem, Xon/Xoff, RTS, and DTR are hardware settings and, therefore, unchangeable.

For example, to change the baud rate to 115.2K, select #2, “Set Baud Rate,” followed by <cr>.

The DS71-MD2 displays the following list of available baud rates:

1 for 300

2 for 600

3 for 1200

4 for 2400

5 for 4800

6 for 9600

7for 19200

8for 38400

9for 57.6K A for 76.8K B for 115.2K Enter Request :

Type "B" for 115.2K baud rate. The DS71- MD2 responds with the new configuration status:

Module 1 Serial Port Configuration :

Port	Device	Baud	Word	Stop	Parity	Xon/	Xoff/	Line	Drive
	Name	Rate	Size	Bits		Xmit	Recv	DTR	RTS

2	Host MODEM	115.2K	8	1	None	Off	Off	High	High
Exit/Save..….......1		Set Parity...….........5
Set Baud Rate….2		Set Xon/Xoff….......6
Set Word Size….3		RTS Line Driver....7
Set Stop Bits..…..4		DTR Line Driver...8
Enter Request :

32

Image 40

Bay Technical Associates DS2-RPC, DS4-RPC, DS73, DS2-RPC DS4-RPC For For 57.6K a for 76.8K B for 115.2K Enter Request

Contents

DS-RPC Data SWITCH/POWER Control BayTech Manual Publication #U140A124-01 AugustPage Iii Page Introduction to the DS-RPC DS71-MD2 Technical Support Page Introduction to the DS-RPC Page Feature Description Action Programmable Features of the DS ModulesDS71 or DS71-MD2 Host Module Programmable Features of the DS Modules con’t Feature Description Action DS71-MD2 Host Module Feature Description Action DS73TP N Etwork Module EIA-232 Serial Connection DS-RPC Quick StartOperation Selecting a Device DS-RPC Module Configuration RPC Installation Unpacking Preparing the Installation Site Power Power UP Sequence Power ON/OFF StateCircuit Breaker RJ-45 Cables and Adapters CablingDS73TP Connection DS71 EIA-232 RJ-45 Pin/Signal Definition DS74 EIA-232 RJ-45 Pin/Signal Definition Modem Connections PIN Detailed Operation Configuration Connecting to the DS-RPCEIA-232 Serial Connection DS71-MD2 only Detailed Operation and Configuration Operation Device a Device B Device C Device D Menu Driven SelectionAscii Character String Binary Mode $BT2,1cr$BTBcrTerminate Binary Mode PPP DIAL-UP Menu Configuration Or this for the DS71-MD2 Status Configuration Serial Port DTR RTS 115.2K None Off High Exit/Save..….......1 Cr. New configuration changes are stored If you have made necessary changes toHost device, type Y for yes, followed by Selecting #1 will give the same results as For For 57.6K a for 76.8K B for 115.2K Enter Request For DTR RTS Host User programmable. Default Port Select Port SelectCode Code is $BT Character Guard is disabled Connect Port Default Connect Port ID Echo is disabledID Echo Header is enabled Login SetupHeader Password Default Password is BTA, disabled. Menu If enabled, the following header and menu appears Auto Connect Port Serial connection Port is disabled Escape Character ........… Disabled Rings toAnswer Rings to Answer is Timeout Default Connectivity Timeout isConnectivity Minutes Default Escape Character is 43, which is EscapeCharacter 2B Hex or a plus sign + Identifies the unit. Default Unit ID is DS71 Unit ResetUnit ID Or DS71-MD2 Driven Ascii Port Device Name …..............................3 Selections 1-8 are fully programmable DS73TP Enter password Dial-UP Default Subnet Mask is Default Dial-Up IP Address isSubnet Mask Default Gateway address is GatewayPrimary DNS Default Primary DNS address is Menu. Default Secondary DNS address isSecondary 0.0 Default Secondary Nbns address is Default Primary Nbns address isNbns Default Password is BTA Default User Name is user1User Name Module Default Module Name is DS73TPName Accessing Main Menu RPC Operation Controlling Receptacles Outlet 1, Outlet 2, Outlet 3, Outlet Change Password DS-RPC Config Outlet Outlet 4 Enter Request Is Enabled Enable/DisableConfirmation RPC Technical Support DS-RPC Model DS-RPC Serial Number ModuleOutlet OUTLET3 Outlet Call BayTech to get a Return Authorization Number REPACKAGING, Shipping and Returning to the Factory FCC Radio Frequency Interface Statement FCC Requirements for the DS71-MD2 FCC Radio Frequency Interface Statement Appendix a SpecificationsTable A.1 Base DS71 Host DS71-MD2 DS74 Appendix B Rockwell Chip SET Modems Command Interpretation Save modem’s configuration in non-volatile memory MY Computer Appendix CMake NEW Connection Properties DIAL-UP Networking Post Dial Terminal Screen Appendix D Drawings DS71 Mechanical Layout DS71-MD2 Mechanical Layout DS74 Mechanical Layout DS73 Mechanical Layout Appendix E Ascii Character Definition Break condition · Rings to Answer · 45, 46 RTS/DTR Line Driver · 29, 31 XON/XOFF ·