JVC manual Example of attachment Speakers SP-VSDT6only, When the Unit is placed vertically

Page 13

Example of attachment (Speakers) (SP-VSDT6 only)

Getting Started

Example of attachment (Speakers) (SP-VSDT6 only)

The speakers can be attached to a wall.

Attach a screw (not supplied) on the wall, then hook the speaker onto the screw.

Wall

•Do not place anything on top of the Center Unit. Doing so may cause the Center Unit to fall, causing malfunctioning and/or injury.

•Do not climb onto the Center Unit or hang from it. Doing so may damage the Center Unit and/or cause injury. Special care must be taken in this respect when there are small children in the home.

•Avoid sandwiching the cords between the Center Unit and wall. This may upset the Center Unit’s balance, causing the Center Unit to fall.

•Make sure that the cords will not interfere with daily activities and that the users will not trip over them. Do not pull the con- nected cords with excessive force.

•Check regularly that none of the screws are loose.

•In the event that the Center Unit has fallen, turn off the power, disconnect its power plug from the power outlet, and contact your dealer for an inspection and repairs. Continued use of the Center Unit may result in a fire or electric shocks.

•Do not place valuables (breakables) underneath the location where the Center Unit is attached. They will be damaged if the Center Unit should fall.

•The manufacturer accepts absolutely no liability for any accidents or damage resulting from inadequate assembly or mount- ing, insufficient strength of attachment, misuse or abuse, or natural disasters.

Now you can plug the AC power cord into the wall outlet, and your System is at your command!

Before operating, verify that the display shows the clock. If malfunctions may occur, re- connect the power cord.

Changing the Display and Control Buttons Settings

You can change the direction of the characters and symbols on the dis-	DISP.SET
play and the assignment of the functions to each control button on the
Unit. Change the settings depending on whether the Unit is placed ver-
tically or horizontally. The factory setting is “V”.
	AC IN

When the Unit is placed vertically

Set the DISP.SET switch to “V”.

H

V

DISP.SET

SOURCE PRESET

VOL

SOURCE

PRESET

VOL

COMPACT COMPONENT SYSTEM

When the Unit is placed horizontally

Set the DISP.SET switch to “H”.

H

V

SOURCE

PRESET

VOL

DISP.SET

SOURCE

PRESET

VOL

CAUTION:

•Be sure to turn off the System when changing the settings.

10

Image 13

Contents COMPACT COMPONENT SYSTEM VS-DT6R/VS-DT7R/VS-DT9RConsists of CA-VSDT6Rand SP-VSDT6 Consists of CA-VSDT7Rand SP-VSDT6Warnings, Cautions and Others SAFETY INSTRUCTIONS 1Installation of the System Features2Power cord IntroductionSpecifications Table of ContentsHow To Put Batteries In the Remote Control AccessoriesGetting Started Using the Supplied Wire Antenna Connecting the FM AntennaUsing the Coaxial Type Connector Not Supplied Rear Panel of the Center UnitRear Panel of the Center Unit Connecting the AM MW/LW AntennaGetting Started The AM loop antenna can be attached to a wallWhen removing Connecting the SpeakersWhen attaching the speaker grilles Removing the speaker grillesConnecting External Equipment Connecting a SubwooferSignal cord not supplied Signal cord not suppliedConnecting the AC Power Cord Connecting an MD Recorder, etc Digital OutputInstalling the Unit on the Stand CAUTIONSExample of attachment Center Unit Installing the Equipment on the WallGetting Started CAUTIONSWhen the Unit is placed vertically Changing the Display and Control Buttons SettingsWhen the Unit is placed horizontally Example of attachment Speakers SP-VSDT6onlyCOMPU Play Using the Remote ControlOn the Remote Control Getting StartedAdjusting the Brightness DIMMER Turning the Power On and OffWhen the System is Turned On Basic Operations2Press the COLOR button on the Remote Control Adjusting the VolumeChanging the Color COLOR VS-DT9Ronly For private listeningReinforcing the Bass Sound AHB PRO on the Remote ControlShowing the Time DISPLAY Tone Control BASS/TREBLETuning In a Station Using the TunerOne Touch Radio 1Press the FM/AM buttonManual Presetting Presetting StationsUsing the Tuner 1Select a band by pressing the FM/AM buttonTo Change the FM Reception Mode To show the RDS signals on the displayReceiving FM Stations with RDS Using the TunerControl To search for a programme by PTY codes3 Press the PTY SEARCH button within 10 seconds againUsing the Tuner To select a programme typeTo Insert a CD Using the CD Player1 Press the % button When playing a CD-Ror CD-RWUsing the CD Player Basics of Using the CD Player - Normal PlayTo Unload a CD To Play a CDRandom Play To Modify the ProgramRepeating Tracks Child LockListening to External Equipment Using External Equipment1Press the MD/AUX button 2 Start playing the external equipmentSetting the Clock Using the TimersRemote Control to set the hour 4 Press the SET buttonUsing the Timers Setting the Daily Timer1Setting the ON time Example 2 Setting the OFF time Example2Press the SLEEP button on the Remote Control Setting the SLEEP Timer7 Press the % button to turn off the Sys- tem 1Play a CD or tune in to the desired sta- tionCleaning the unit Care And MaintenanceCompact Discs Moisture CondensationSymptom TroubleshootingPossible Cause ActionSpecifications