JVC P-VSDT6 Basic Operations, Turning the Power On and Off, Turning the System On, CD-inindicator

Page 15
Basic Operations

Basic Operations

Operation indicators

Panel

STANDBY/ON

1

2

3

 

 

4

5

6

PLAY MODE

 

 

 

 

 

 

REPEAT

 

7

8

9

 

 

10

 

 

FM MODE

% indicator

 

+10

 

BASS

 

 

TREBLE

 

BASS Turning the Power On and OffTurning the System OnPress the % button. TREBLE

SET

MD/AUX

CANCEL

SOURCE

PRESET

VOL

VOL +/–

AHB PRO COLOR

(VS-DT9R only)

PTY

PTY

 

TA/NEWS

 

SEARCH

SELECT

/INFO

DIMMER

FM/AM

MODE

DIMMER

SLEEP

 

DISPLAY

 

 

 

AHB PRO

 

DISPLAY

 

VOLUME +/–

COLOR

CLOCK

OPEN/

 

/TIMER

CLOSE

 

 

 

 

 

VOLUME

 

 

 

 

 

DISPLAY

COMPACT COMPONENT SYSTEM

Illumination

Turning the Power On and Off

Turning the System On

Press the % button.

The display comes on and “HELLO” is displayed once. The operation indicators light on the Panel. (The Panel opens automatically if the Unit is placed vertically and the DISP.SET switch on the rear of the Unit is set to “V”.)

The System comes on ready to continue in the mode it was in when the power was last turned off.

■For example, if the last thing you were doing was listen- ing to a CD, you are now ready to listen to a CD again. If you wish, you can change to another source.

■If you were listening to the Tuner last, the Tuner comes on playing the station it was last set to.

Turning the System Off

Press the % button again.

The Panel closes if it has been opened.

“GOOD BYE” is displayed and the display goes out, except for the clock display. The %indicator (red) remains lit and the rest of the operation indicators go out.

■Some power is always consumed even though power is turned off (called Standby Mode).

■To switch off the System completely, unplug the AC power cord from the wall outlet. When you unplug the AC power cord, the clock will be reset to 0:00 after about 20 minutes.

Power Save Mode

You can reduce the power consumption in standby mode.

Press the DISPLAY button on the Remote Control when the System is turned off.

•The clock display goes out.

CD-in indicator

While a disc is loaded on the Unit, the CD-in indicator is lit on the display.

STEREO

•The CD-in indicator lights while using the Tuner or external equipment and does not light during CD oper- ations.

Adjusting the Brightness (DIMMER)

(Using the Remote Control)

You can adjust the brightness of the backlighting for the dis- play and the illumination on the cover.

When the System is Turned On

Each time you press the DIMMER button on the Remote Control, the brightness of the backlighting and the illumina- tion on the cover change as follows:

Display
Backlighting
Illumination

 

 

 

DIMMER OFF

Bright

Bright

 

 

 

DIMMER 1

Slightly Dark

Slightly Dark

 

 

 

DIMMER 2

Dark

Off

 

 

 

•When the System is turned off once, then turned on again, the brightness setting will be restored to the previous one since the setting is stored in memory.

12

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Consists of CA-VSDT7Rand SP-VSDT6 VS-DT6R/VS-DT7R/VS-DT9RCOMPACT COMPONENT SYSTEM Consists of CA-VSDT6Rand SP-VSDT6Warnings, Cautions and Others SAFETY INSTRUCTIONS Introduction Features1Installation of the System 2Power cordSpecifications Table of ContentsAccessories How To Put Batteries In the Remote ControlGetting Started Rear Panel of the Center Unit Connecting the FM AntennaUsing the Supplied Wire Antenna Using the Coaxial Type Connector Not SuppliedThe AM loop antenna can be attached to a wall Connecting the AM MW/LW AntennaRear Panel of the Center Unit Getting StartedRemoving the speaker grilles Connecting the SpeakersWhen removing When attaching the speaker grillesSignal cord not supplied Connecting a SubwooferConnecting External Equipment Signal cord not suppliedCAUTIONS Connecting an MD Recorder, etc Digital OutputConnecting the AC Power Cord Installing the Unit on the StandCAUTIONS Installing the Equipment on the WallExample of attachment Center Unit Getting StartedExample of attachment Speakers SP-VSDT6only Changing the Display and Control Buttons SettingsWhen the Unit is placed vertically When the Unit is placed horizontallyGetting Started Using the Remote ControlCOMPU Play On the Remote ControlBasic Operations Turning the Power On and OffAdjusting the Brightness DIMMER When the System is Turned OnFor private listening Adjusting the Volume2Press the COLOR button on the Remote Control Changing the Color COLOR VS-DT9RonlyTone Control BASS/TREBLE on the Remote ControlReinforcing the Bass Sound AHB PRO Showing the Time DISPLAY1Press the FM/AM button Using the TunerTuning In a Station One Touch Radio1Select a band by pressing the FM/AM button Presetting StationsManual Presetting Using the TunerUsing the Tuner To show the RDS signals on the displayTo Change the FM Reception Mode Receiving FM Stations with RDS10 seconds again To search for a programme by PTY codesControl 3 Press the PTY SEARCH button withinUsing the Tuner To select a programme typeWhen playing a CD-Ror CD-RW Using the CD PlayerTo Insert a CD 1 Press the % buttonTo Play a CD Basics of Using the CD Player - Normal PlayUsing the CD Player To Unload a CDChild Lock To Modify the ProgramRandom Play Repeating Tracks2 Start playing the external equipment Using External EquipmentListening to External Equipment 1Press the MD/AUX button4 Press the SET button Using the TimersSetting the Clock Remote Control to set the hour2 Setting the OFF time Example Setting the Daily TimerUsing the Timers 1Setting the ON time Example1Play a CD or tune in to the desired sta- tion Setting the SLEEP Timer2Press the SLEEP button on the Remote Control 7 Press the % button to turn off the Sys- temMoisture Condensation Care And MaintenanceCleaning the unit Compact DiscsAction TroubleshootingSymptom Possible CauseSpecifications
Top Page Image Contents