TP-Link TL-R4299G manual Configure the IP address as shown in -4.After that, click OK

Page 13

TL-R4299GDual-WAN SMB Broadband Router User Guide

Step 4: Configure the IP address as shown in Figure 3-4.After that, click OK.

Figure 3-4

)Note:

You can configure the PC to get an IP address manually, select “Obtain an IP address automatically” and “Obtain DNS server address automatically” in the screen above.

Now, you can run the Ping command in the command prompt to verify the network connection. Please click the Start menu on your desktop, select run tab, type cmd in the field, and then type ping 192.168.1.1 on the next screen, and then press Enter.

If the result displayed is similar to the screen below, the connection between your PC and the Router has been established.

Figure 3-5

7

Image 13

Contents TL-R4299G Dual-WAN SMB Broadband Router Copyright & Trademarks FCC Statement Package contents Contents Appendix a Specifications Appendix B FAQ Appendix C Glossary Overview of the Router FeaturesTL-R4299G Panel Layout ConventionsFront Panel LED Descriptions Name ActionSystem Requirements Installation Environment RequirementsRear Panel Connecting the Router Configure PC Quick Installation GuideDual-WAN SMB Broadband Router User Guide Configure the IP address as shown in -4.After that, click OK Is the connection between your PC and the Router correct? LoginDual-WAN SMB Broadband Router User Guide TL-R4299GDual-WAN SMB Broadband Router User Guide Status Configuring the RouterDual-WAN SMB Broadband Router User Guide Network Quick Setup1 LAN Dynamic IP 2 WANDual-WAN SMB Broadband Router User Guide Static IP PPPoE TL-R4299GDual-WAN SMB Broadband Router User Guide Dual-WAN SMB Broadband Router User Guide BigPondCable L2TP Dual-WAN SMB Broadband Router User Guide Pptp Dual-WAN SMB Broadband Router User Guide Network service detection Flow Balance MAC CloneTo add a dispatch rule Balance Policy Other configurations for the entries as shown in FigureClick Save Dual-WAN SMB Broadband Router User Guide WAN Port Parameter Dhcp Dhcp SettingsDhcp Clients List To add/modify a reserved IP address Address ReservationVirtual Servers ForwardingTo add/modify a virtual server entry Port Triggering To add/modify a port triggering entry 3 DMZ To assign a computer or server to be a DMZ server UPnPFirewall SecurityIP Filtering To add/modify an IP Address filtering entry TL-R4299GDual-WAN SMB Broadband Router User Guide To add or modify a Domain Filtering entry Domain FilteringMAC Filtering Dual-WAN SMB Broadband Router User Guide Screen ¾ Scan Attack Defence ¾ Dubious Packet Defence ¾ DoS Attack Defence¾ Packet Defence with IP option Static RoutingTo add/modify a static routing entry Session Limit Session LimitTo add/modify a session limit entry Session List QoSQoS Rules List QoS SettingsTo add/modify a QoS rule Setting, ARP List Binding Setting10 IP & MAC Binding To find a specific IP & MAC binding entry To add/modify an IP & MAC binding entryARP List Dynamic DNS To set up for Dyndns DDNS, follow these instructionsDyndns Ddns PeanutHull Ddns To set up for PeanutHull DDNS, follow these instructionsComexe Ddns To set up for Comexe DDNS, follow these instructions Switch SettingPort Mirror Port StatisticsPort Rate Control Port Parameter Port Status Port Vlan System ToolsTo configure the system time manually Time SettingsTo configure the system automatically Firmware Factory DefaultsTo back up the Router’s current settings Backup and RestoreTo restore the Router’s settings RebootPassword Remote Management System LogStatistics WAN Speed Detect Dual-WAN SMB Broadband Router User Guide IP NAT Table NAT Source Port SettingsPhysical and Environment GeneralAppendix B FAQ Want to use Netmeeting, what do I need to do? SaveMethod one Use Virtual Server Want to build a WEB Server on the LAN, what should I do? Method two Use DMZ HostFigure B-6 Appendix C Glossary