JVC CA-WMD90R manual Tuning in a Station, Presetting Stations, To change the FM reception mode

Page 17

Continued

When using the number buttons on the remote control, make sure that they are ready for tuner operations.

•Pressing FM/AM on the remote control makes the number buttons ready for tuner operations.

Tuning in a Station

On the unit ONLY:

1 Press FM/AM.

The unit automatically turns on and tunes in the previously tuned station (either FM or AM–MW/LW).

•Each time you press the button, the band alternates between FM and AM.

2 Rotate the left jog dial quickly until the station frequencies change in the main display.

•Clockwise: to increase the frequencies.

•Counterclockwise: to decrease the frequencies.

The unit starts searching stations and stops when a station of sufficient signal strength is tuned in (the TUNED indicator lights).

If a program is broadcast in stereo, the STEREO indicator also lights.

To stop during searching, rotate the left jog dial briefly again.

When you rotate the left jog dial slowly

The frequency changes step by step.

To change the FM reception mode

When an FM stereo broadcast is hard to receive or noisy, press FM MODE on the remote control so that “MONO” appears in the main display. Reception improves.

To restore the stereo effect, press FM MODE again so that “AUTO” appears in the main display.

In this stereo mode, you can hear stereo sounds when a program is broadcast in stereo.

Presetting Stations

You can preset 30 FM and 15 AM (MW/LW) stations at random.

In some cases, test frequencies have been already memorized for the tuner since the factory examined the tuner preset function before shipment. This is not a malfunction. You can preset the stations you want into memory by following the presetting method.

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the unit ONLY:

1 Tune in the station you want to preset.

• See “Tuning in a Station” to the left.

2 Press SET.

The current preset number starts flashing.

3 Rotate the right jog dial to select a preset number.

•Clockwise: to increase the preset numbers.

•Counterclockwise: to decrease the preset numbers.

4 Press SET again.

The tuned station in step 1 is stored in the preset number selected in step 3.

•Storing a new station on a used number erases the previously stored one.

When you unplug the AC power cord or if a power failure occurs

The preset stations will be erased in a few days. If this happens, preset the stations again.

– 14 –

Page 16 Page 18
Image 17
Page 16 Page 18
Contents CA-WMD90R If in Doubt Consult a Competent Electrician Class Laser Product Introduction PrecautionsContents Become familiar with the buttons and controls on your unit Location of the Buttons and ControlsDisplay Window Amplifier/tuner section Front PanelMD deck a section MD deck B sectionRemote Control Remote ControlConnecting Antennas Putting the Batteries into the Remote ControlGetting Started UnpackingYou can connect the speakers using the speaker cords Connecting SpeakersAM antenna To connect an outdoor AM antennaTo connect a cassette deck Connecting Other EquipmentTo start the display demonstration manually Output terminalBasic and Common Operations Front panel Remote controlTurning On the Power and Selecting the Sources Setting the ClockAdjusting the Volume To adjust the clock againTo use your own sound mode Creating Your Own Sound Mode Manual ModeReinforcing the Bass Sound Activating the Surround EffectListening to FM and AM MW/LW Broadcasts To change the FM reception mode Tuning in a StationPresetting Stations Changing the RDS Information Tuning in a Preset StationReceiving FM Stations with RDS Alarm Òback to the beginning Switching to a Program Type of Your Choice TemporarilySearching for Programs by PTY Codes PTY Search PTY Select flashes in the main displayMore about the EON function Alarm functionTest function R. M Description of the PTY codesPlaying Back CDs Playing Back the Entire Discs Continuous Play Loading CDsBasic CD Operations To exchange CDs during playback of anotherTo check the program contents To go to another track directly using the number buttonsProgramming the Playing Order of the Tracks Program Play To go to another trackRepeating Tracks or CDs Repeat Play Playing at Random Random PlayProhibiting Disc Ejection Disc Lock Tracks of all loaded CDs will play at randomPlaying Back MDs CancelWhen using MD deck B When using MD deck aLoading MDs Playing Back the Entire MD Continuous PlayWhile playing an MD, you can do the following operations Basic MD OperationsTo change the display Indications Tracks are played in the order you have programed Insert an MDInsert MDs Press #/ 8 on MD deck B or MD B 6 on the remote controlTracks of the loaded MDs will play at random Repeating Tracks Repeat PlayTo prohibit disc ejection Disc Lock FM/AM Tape AUX Recording on MDsAbout the track marks Before You Start RecordingTo avoid erasing important recordings Recording is only possible on MD deck BRecording the External AUX Equipment AUX Recording When recording from the cassette deck, start playing a tapeTo check the remaining time Press AUX againSynchronized Recording Various Recording FunctionsMD to MD Synchronized Recording Start playing the source on the external equipmentCD to MD Synchronized Recording To confirm the recording contentsPress Start Enter On the unit only Load a CDFirst Track Recording Single Track RecordingOn the unit only Load CDs Rotate the left jog dial to select the recordable MDOn the unit only Prepare a CD or an MD as the source sound Listening Edit RecordingRepeat to program other tracks To stop any time during editing process and startTriple Recording Prepare the source you want to record from Long RecordingLong REC lamp also lights Recording starts from MD 1, MD 2 to MDEditing MDs Introducing MD Editing Functions To join the divided tracks again, see the Join function Divide FunctionPress MD Edit Move Function Join FunctionTo divide the joined tracks, see the Divide function Rotate the right jog dial until Move ? appears Press SETErase Function CANCEL, then select the correct track number againEdit MD deck B starts playing the MDALL Erase Function TUV Assigning Titles to MDsAssigning a Title Using the Unit Press Enter Start to finish the current title entry Changing the TitleYou can make a correction or change the title Make sure that the character you want to change is flashingPress MD Title Input Track title entry indication mode appears whenPress the button for the next character you want to input Press Enter to finish the current title entryName Sleep Using the TimersHow Recording Timer actually works Using Recording TimerTo turn on or off Recording Timer after its setting is done To turn on the Recording Timer, press SETHow Daily Timer actually works Using Daily TimerVolume level will be set to 20 loud Volume level will be set the previous level whenHow Sleep Timer actually works Timer PriorityUsing Sleep Timer To clean the CD MaintenanceGeneral Notes Handling CDsAdditional Information Utoc User Table Of ContentsMD Disc Types Atrac Adaptive TRansform Acoustic CodingMD limitations Sound Skip Guard MemoryPossible Cause TroubleshootingMD Messages Signification SolutionSpecifications JVC 0399KSMMDWJEM
Top Page Image Contents