Selecting the Front Speakers | Remote |
| NOT |
When you have connected two pairs of the front speakers, you can select which to use.
To use the speakers connected to the FRONT SPEAKERS 1
terminals, press SPEAKERS ON/OFF 1 so that the SPEAKERS 1 indicator lights up on the display.
•Make sure that the SPEAKERS 2 indicator is not lit.
To use the speakers connected to the FRONT SPEAKERS 2
terminals, press SPEAKERS ON/OFF 2 so that the SPEAKERS 2 indicator lights up on the display.
•Make sure that the SPEAKERS 1 indicator is not lit.
To use both sets of the speakers connected to the FRONT SPEAKERS 1 and 2 terminals, press SPEAKERS ON/OFF 1
and 2 so that the SPEAKERS 1/2 indicators light up on the display.
ANALOG
L | R LINEAR PCM |
SPEAKERS 1 2
VOLUME
Ex. When both sets of the speakers selected.
Note:
When playback analog sources or digital
To use neither sets of the speakers connected to the FRONT SPEAKERS 1 and 2 terminals, press SPEAKERS ON/OFF 1 and 2 so that the SPEAKERS 1/2 indicators go off from the display. The HEADPHONE indicator lights up and “HEADPHONE” appears on the display.
•Activating the speakers turns on the Surround and DSP modes previously selected.
Listening with headphones only:
Deactivate both sets of the front speakers, and connect headphones to the PHONES jack.
•Make sure that all the Speaker indicators are not lit.
You can enjoy the sound effects through the headphones when Surround or DSP mode is
(3D H PHONE) mode.
•“3D H PHONE” appears and the DSP and HEADPHONE indicators light up on the display. (For details, see page 32.)
Note:
3D Headphone (3D H PHONE) mode is not valid for DVD MULTI playback mode.
CAUTION:
Be sure to turn down the volume:
•Before connecting or putting on headphones, as its high volume can damage both the headphones and your hearing.
•Before turning on the speakers again, as its high volume may come out of the speakers.
Turning On and Off the | Remote |
Subwoofer Sound | NOT |
|
You can cancel the subwoofer sound output even though you have connected a subwoofer and have set “SUB WOOFER” to “YES” (see page 23).
Press SUBWOOFER OUT ON/OFF to cancel the subwoofer sound output.
Each time you press the button, subwoofer sound output is deactivated (“SUBWFR OFF”) and activated (“SUBWFR ON”) alternately.
•When subwoofer output is canceled, the SUBWFR indicator goes off. Bass sounds (and LFE signals) will be emitted through the front speakers (except for DVD MULTI playback mode).
•When subwoofer sound output is activated, subwoofer output level can be adjusted (see pages 28 and 29).
Notes:
•SUBWOOFER OUT ON/OFF button does not work when you set “SMALL” for the front speakers on the Speaker size setting (see page 23) or using Quick Speaker Setup (see page 21).
•You cannot activate the subwoofer output when you have set “SUB WOOFER” to “NO” (see pages 21 and 23).
•When you change the “SUB WOOFER” setting from “NO” to “YES” (see page 23), subwoofer output is automatically activated.
Selecting the Analog or Digital Input Mode
When you have connected digital source components using the digital terminals (see page 12), change the input mode for these components to the digital input mode.
Before you start, remember...
The digital input terminal setting should be correctly done for the sources you want to select the digital input mode (see “Setting the digital input terminals” on pages 25 and 26).
1.Press one of the source selection buttons (DVD, VCR, TV SOUND/DBS, CD, or TAPE/CDR*) for which you want to change the input mode.
*If TAPE is selected as the source, digital input mode is not available. To change the source name to CDR, see “Changing the Source Name” on page 17.
Continued on the next page
15