JVC RX-888VBK Digital Input Digital in Terminal Setting, Showing the Text Information on Display

Digital Input (DIGITAL IN) Terminal Setting

When you use the digital input terminals, you have to register what components are connected to which terminals (DIGITAL IN 1/2/3).

Before you start, remember....

2. Press INPUT ANALOG/DIGITAL	INPUT
to change the input mode.	ANALOG/DIGITAL

•Each time you press the button, the input mode alternates between the digital input and analog input.

From the remote control:

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the front panel ONLY:
1. Press SETTING repeatedly until	SETTING
“DIGITAL IN” appears on the
display.

The display changes to show the current setting.

1.Press the source selecting button (CD, TAPE/MD, TV/DBS*, or

DVD) for which you want to change the input mode from analog input to digital input.

2.Press ANALOG/DIGITAL to change the input mode.

DVD	DVD MUILTI	CD	TAPE/MD
TV/DBS	VIDEO	PHONO	FM/AM
VCR 1	VCR 2

ANALOG/DIGITAL

DIGITAL 2 terminal setting

		VOLUME
DIGITAL 1 terminal setting	DIGITAL 3 terminal setting
		MULTI JOG

2.Turn MULTI JOG to select the appropriate digital terminal setting.

• As you turn it, the display changes to show the following:

1 DBS 2 DVD 3 CD	Ò	1 MD 2 DVD 3 CD	Ò
1 MD 2 DBS 3 CD	Ò	1 MD 2 DBS 3 DVD Ò
1 CD 2 DVD 3 MD	Ò	1 CD 2 DBS 3 MD	Ò
1 CD 2 DBS 3 DVD	Ò	1 DVD 2 CD 3 MD	Ò
1 DVD 2 DBS 3 MD Ò		1 DVD 2 DBS 3 CD	Ò
1 DBS 2 CD 3 MD	Ò	1 DBS 2 DVD 3 MD Ò
(back to the beginning)

Note:

When shipped from the factory, the DIGITAL IN terminals can be used as the digital input for the following components.

•Each time you press the button, the input mode alternates between the digital input and analog input.

Notes:

*Before pressing TV/DBS, make sure that the remote control mode selector on the remote control is set to “CATV/DBS.”

•Once you have set the digital input for these components, it is always used every time you select these components as the source.

Showing the Text Information on the

Display

When you have connected an MD recorder or CD player equipped with TEXT COMPU LINK remote control system (see page 37), you can show the text information, such as disc title or track title, on the display of this receiver. To show it on the display, follow the procedure below.

Before you start, remember....

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

•DIGITAL 1 (coaxial): For DBS tuner

•DIGITAL 2 (optical): For DVD player

•DIGITAL 3 (optical): For CD player

On the front panel ONLY:

1. Press SETTING repeatedly until “FL DISPLAY” appears on the display.

SETTING

Selecting the Analog or Digital Input

Mode

When you have connected some components such as CD player, MD recorder, DVD player and the DBS tuner using digital terminals (see page 8), you need to change the input mode for these components to the digital input.

On the front panel:

1. Turn SOURCE SELECTOR until

SOURCE SELECTOR

the source (CD, MD, DBS, or DVD) for which you want to change the input mode from analog input to digital input appears on the display.

The display changes to show the current setting.

MULTI JOG

2.Turn MULTI JOG to select either the source name or the text information to be shown on the display.

• As you turn it, the display changes to show the following:

NORMAL TEXT

NORMAL: Source name appears during play.

TEXT: Text information appears during play.

Notes:

•Though you have selected “TEXT,” the source name such as “CD” or “MD” appears if a playing disc has no text information.

•Though you have selected “NORMAL,” the setting is changed to “TEXT” in the following case: