JVC RX-888VBK manual Activating the DSP Modes

DOLBY SURROUND

DOLBY SURROUND

On the front panel:

You can also use the buttons on the front panel to adjust the Surround modes. However, no test tone is available when using the buttons on the front panel. So, make adjustments while listening to the sound of the source played back.

Activating the DSP Modes

You can use only one DSP mode at a time. When a DSP mode is activated, another DSP mode is canceled if in use.

1. Press DSP MODE repeatedly until “THEATER” or “DIG THEATER” appears on the display.

DSP MODE

For Dolby Pro Logic, Dolby Digital, and DTS Digital Surround

On the front panel:

1. Press DOLBY/DTS SURROUND	DOLBY/DTS
	SURROUND ON/OFF

•When “THEATER” is selected, the PRO LOGIC, DSP, and THEATER indicators light up on the display.

•When “DIG THEATER” is selected, the DSP and THEATER indicators light up on the display.

2. Adjust the speaker output levels.	BALANCE/SURROUND
1) Press BALANCE/SURROUND		ADJUST
ADJUST repeatedly until one of the
indications appears on the display.
“CENTER LEVEL”:
To adjust the center speaker level.
“REAR L LEVEL”:
To adjust the left rear speaker level.
“REAR R LEVEL”:
To adjust the right rear speaker level.		MULTI JOG

2)Turn MULTI JOG to adjust the selected speaker output level (from –10 dB to +10 dB).

3)Repeat 1) and 2) to adjust the other speaker output levels.

3.Adjust the center tone.

1)	Press BALANCE/SURROUND	BALANCE/SURROUND
	ADJUST repeatedly until “CENTER		ADJUST
	TONE” appears on the display.
	The display changes to show the current
2)	setting.
	Turn MULTI JOG to select the center		MULTI JOG

tone level you want.

•As you turn it, the display changes to show the following:

SOFT 2SOFT 1FLATSHARP 1SHARP 2

4. Adjust the effect level.	BALANCE/SURROUND
1) Press BALANCE/SURROUND
		ADJUST
ADJUST repeatedly until “DSP
EFFECT” appears on the display.

The display changes to show the current setting.

MULTI JOG

2)Turn MULTI JOG to select the effect level.

•As you turn it, the effect level changes as follows:

DSP EFFECT 1DSP EFFECT 2 DSP EFFECT 3

DSP EFFECT 5 DSP EFFECT 4

As the number increases, JVC Theater Surround becomes stronger.

ON/OFF so that the lamp on the

button lights up.

• Each time you press the button, the Dolby/ DTS Surround turns on and off alternately.

2. Select and play a sound source.

• To enjoy Dolby Pro Logic, play back a software encoded with

Dolby Surround and labeled with mark.

•To enjoy Dolby Digital, play back a software encoded with Dolby Digital and labeled with D I G I T A L mark.

•To enjoy DTS Digital Surround, play back a software encoded

with DTS Digital Surround and labeled with mark.

To cancel the Dolby/DTS Surround mode

Press DOLBY/DTS SURROUND ON/OFF	DOLBY/DTS
	SURROUND ON/OFF
again so that the lamp on the button goes off.
(“SURROUND OFF” appears on the display.)

From the remote control:
1. Press SURROUND ON/OFF so	SURROUND
that the lamp on the DOLBY/DTS	ON/OFF
SURROUND ON/OFF button on

the front panel lights up.

•Each time you press the button, the Dolby/DTS Surround turns on and off alternately.

•You can also turn on Dolby/DTS Surround by pressing SURROUND MODE. (See page 22 for more details.)

2.Select and play a sound source.

•To enjoy Dolby Pro Logic, play back a software encoded with

Dolby Surround and labeled with mark.

•To enjoy Dolby Digital, play back a software encoded with Dolby Digital and labeled with D I G I T A L mark.

•To enjoy DTS Digital Surround, play back a software encoded

with DTS Digital Surround and labeled with mark.

To cancel the Dolby/DTS Surround mode

Press SURROUND ON/OFF again.	SURROUND
(“SURROUND OFF” appears on the display.)	ON/OFF