JVC RX-888VBK manual Adjusting the 3D-PHONIC Modes, Adjusting the DAP Modes

IMPORTANT:

When using the remote control, check to see if its

remote control mode selector is set to the correct AUDIO/

3. Press EFFECT to select an effect	EFFECT
level you want.	7/P

• Each time you press the button, the effect

position:

TV/VCR

level changes as follows:

To operate this receiver, set it to “AUDIO/TV/

CATV/DBS

VCR” (except when selecting the DBS tuner as the source).

Adjusting the 3D-PHONIC Modes

Once you have adjusted the 3D-PHONIC modes, the adjustment is memorized for each 3D-PHONIC mode.

Before you start, remember...

•Make sure that you have set the speaker information correctly (see page 14).

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the front panel:

DSP MODE

1. Press DSP MODE repeatedly until “3D ACTION (or 3D DIGITAL)” or “3D THEATER” appears on the display.

The 3D-PHONIC, DSP, PRO LOGIC and selected 3D-PHONIC mode indicators also light up on the display.

DSP EFFECT 1 DSP EFFECT 2 DSP EFFECT 3

DSP EFFECT 5 DSP EFFECT 4

As the number increases, the selected 3D-PHONIC mode becomes stronger.

Adjusting the DAP Modes

Once you have adjusted the DAP modes, the adjustment is memorized for each DAP mode.

Before you start, remember...

•Make sure that you have set the speaker information correctly (see page 14).

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

•You cannot adjust the rear speaker output level when you have set “REAR SPK” to “NONE.” See page 14.

•When the DAP mode is used with the SEA mode (see page 19), sounds may be distorted. If this happens, turn off the SEA mode.

On the front panel:

2.Adjust the effect level.

1)Press BALANCE/SURROUND ADJUST repeatedly until “DSP EFFECT” appears on the display. The display changes to show the current setting.

2)Turn MULTI JOG to select the effect level.

•As you turn it, the effect level changes as follows:

BALANCE/SURROUND

ADJUST

MULTI JOG

1. Press DSP MODE repeatedly until	DSP MODE
the DAP mode — LIVE CLUB,
DANCE CLUB, HALL, or
PAVILION — appears on the
display.

The DSP and the selected DAP mode indicators also light up on the display.

•When you have set “REAR SPK” to “NONE,” the 3D- PHONIC indicator also lights up.

DSP EFFECT 1DSP EFFECT 2 DSP EFFECT 3

DSP EFFECT 5	DSP EFFECT 4
As the number increases, the selected 3D-PHONIC mode
becomes stronger.
From the remote control:
1. Press SURROUND MODE		SURROUND
repeatedly until “3D ACTION (or		MODE

3D DIGITAL)” or “3D THEATER” appears on the display.

The 3D-PHONIC, DSP, PRO LOGIC and selected 3D-PHONIC mode indicators also light up on the display.

SOUND

2. Press SOUND.

The 10 keys are activated for sound adjustments.

2.Adjust the speaker output levels.

1)Press BALANCE/SURROUND ADJUST repeatedly until one of the indications appears on the display. “REAR L LEVEL”:

To adjust the left rear speaker level. “REAR R LEVEL”:

To adjust the right rear speaker level.

2)Turn MULTI JOG to adjust the selected speaker output level (from –10 dB to +10 dB).

3)Repeat 1) and 2) to adjust the other speaker output level.

BALANCE/SURROUND

ADJUST

MULTI JOG