ProForm PATL30706.0 user manual HOW to USE a Preset Program, Select a preset program

Page 18
Current Period

HOW TO USE A PRESET PROGRAM

1 Insert the key into the console.

See HOW TO TURN ON THE POWER on page 16.

2 Select a preset program.

To select one of the ten

preset programs, press

the Program Select but-

ton repeatedly until one of the programs num- bered “P–1” through

“P–10” appears in the display. When a preset pro- gram is selected, the maximum incline setting of the program and the maximum speed setting of the program will flash in the display for a few sec- onds. The display will also show how long the pro- gram will last. A profile of the speed settings of the program will scroll across the matrix in the upper right corner of the display.

Press the Start button or the Speed increase

3 button to start the program.

A moment after the button is pressed, the tread- mill will automatically adjust to the first speed and incline settings of the program. Hold the handrails and begin walking.

Each program is divided into several one-minute periods. One speed setting and one incline setting are programmed for each period. Note: The same speed setting and/or incline setting may be pro- grammed for two or more consecutive periods.

The speed setting for the first period will be

shown in the flashing Current Period column of the matrix in the dis- play. (The incline set-

tings are not shown in the matrix.) The speed set- tings for the next four periods will be shown in the columns to the right.

When only three seconds remain in the first period of the program, both the Current Period column and the column to the right will flash and a series of tones will sound. If the speed and/or incline of the treadmill is about to change, the speed setting and/or the incline setting will flash in the display to alert you.

When the first period is completed, all speed set- tings will move one column to the left. The speed setting for the second period will then be shown in the flashing Current Period column and the tread- mill will automatically adjust to the speed and in- cline settings for the second period. Note: If all five of the indicators in the Current Period column are lit, the speed settings may move downward so that only the highest indicators appear in the matrix.

The program will continue in this way until the speed setting for the last period is shown in the Current Period column and the last period ends. The walking belt will then slow to a stop.

If the speed or incline setting for the current period is too high or too low, you can manually override the setting by pressing the Speed or Incline but- tons. Every few times a Speed button is pressed, an additional indicator will appear or disappear in the Current Period column; if any of the columns to the right of the Current Period column have the same number of lit indicators as the Current Period column, an additional indicator may appear or disappear in those columns as well. Important:

When the current period of the program ends, the treadmill will automatically adjust to the speed and incline settings for the next period.

To stop the program temporarily, press the Stop button. The time will begin to flash in the display. To restart the program, press the Start button or the Speed increase button. The walking belt will begin to move at 2 Km/H. When the next period of the program begins, the treadmill will automatically adjust to the speed and incline settings for the next period. To end the program, press the Stop button, remove the key, and then reinsert the key.

4 Follow your progress with the display.

See step 5 on page 17.

5 Measure your heart rate if desired.

See step 6 on page 17.

6 Turn on the fan if desired.

See step 7 on page 17.

When the program is completed, remove the

7 key from the console.

See step 8 on page 17.

18

Image 18
Contents Please Contact OUR CUS- Tomer Service Department Directly QUESTIONS?Model No. PATL30706.0 Serial No Table of Contents Important Precautions Page Before YOU Begin Back Right SideAssembly Make sure that the power cord is unplugged Outer side of the Frame Spacer facing Nut yetPage Page Tighten the four Screws Front ViewTighten the Screws yet. Next, tighten two Do not overtighten the Frame Bolts View From AboveTo overtighten the Screws Be careful not to overtighten the ScrewsPage Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleSelect the manual mode HOW to Turn on the PowerHOW to USE the Manual Mode Insert the key into the consoleMeasure your heart rate if desired Avoid moving Your hands. When your pulseFollow your progress with the display Turn on the fan if desiredHOW to USE a Preset Program Select a preset programWhen the program is completed, remove Key from the console HOW to Connect Your MP3 Player or CD Player HOW to Connect Your Portable StereoAudio Cable HOW to Connect Your Home Stereo HOW to Connect Your ComputerHOW to Connect Your VCR Press the Play button on your MP3 player, CD Player, or VCRDirectly from OUR WEB Site Information MODE/DEMO Mode Follow the on-line instructions to start ProgramReturn to the treadmill and stand on the foot HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USETroubleshooting Problem The power turns off during useTop View Problem The walking belt slows when walked on Workout Guidelines Conditioning GuidelinesExercise Intensity Exercise FrequencyPart LIST-Model No. PATL30706.0 Key No. Qty DescriptionExploded DRAWING-Model No. PATL30706.0 Ordering Replacement Parts Limited WarrantyGoodfamily, Inc