ProForm PMTL39708.0 user manual Nected PROPERLY, the Console MAY, Be Damaged When the Power is

Page 11

11. Set the Console (87) face down on a soft sur-

11

 

 

 

Console

 

face to avoid scratching the Console. Identify

90

 

1

 

the Right Handrail (90), which has a large hole

 

 

Wire

 

in the location shown. Hold the Right Handrail

 

 

 

 

Large

 

near the Console. Attach the console ground

 

 

 

 

 

wire to the Right Handrail with a #8 x 1/2" Screw

 

Console

 

 

Hole

1

(22).

 

 

 

 

Next, insert the console wire into the large hole

 

Ground Wire

 

 

 

in the Right Handrail (90) and out of the top as

 

 

 

 

 

 

shown. Attach the Right Handrail with three

 

 

 

22

 

 

M4.2 x 19mm Screws (1). Make sure that no

 

 

 

 

 

wires are pinched. Start all three Screws be-

 

 

 

 

 

 

fore tightening any of them; do not over-

 

87

 

 

 

 

tighten the Screws.

 

 

 

 

 

12. Attach the Left Handrail (89) to the console as-

12

 

 

 

Console

 

sembly with three M4.2 x 19mm Screws (1).

 

 

 

 

Start all three Screws before tightening any

 

 

 

 

Assembly

 

of them; do not overtighten the Screws.

 

89

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

13. Have a second person hold the console assem-

13

 

 

 

 

 

bly near the Right Upright (78). Cut the ties on

 

 

 

Console Assembly

 

the Right Handrail (90) and the Left Handrail (not

 

 

 

 

 

shown). If necessary, press the four Cage Nuts

 

 

 

 

 

 

(38) back into place.

 

 

 

 

 

 

Connect the Wire Harness (77) to the console

 

 

 

wire. See the inset drawing. The connectors

 

 

 

should slide together easily and snap into

 

 

 

place. If they do not, turn one connector and try

 

 

 

again. IF THE CONNECTORS ARE NOT CON-

 

 

 

NECTED PROPERLY, THE CONSOLE MAY

 

Ties

 

BE DAMAGED WHEN THE POWER IS

90

Console

TURNED ON. Remove the wire ties from the

 

Wire Harness and the console wire. Then, insert

38

Console Wire

Wire

the connectors into the Right Upright (78).

77

 

Set the console assembly on the Right Upright

Wire Tie

 

(78) and the Left Upright (not shown). Make sure

78

 

77

that no wires are pinched.

 

11

Image 11
Contents On the WEB QUESTIONS?Model No. PMTL39708.0 Serial No Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MTTable of Contents Important Precautions Treadmill until it is properly assembled. See By an authorized service representative onlyCuit breaker to the off position when Before YOU Begin Assembly Do not fully fold the Frame yet Make sure that the power cord is unpluggedTouch the Upright do not fully tighten Bolts yet Page Tighten the Bolts yet Nected PROPERLY, the Console MAY Be Damaged When the Power isPage PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Features of the Console Console DiagramInsert the key into the console HOW to Turn on the PowerHOW to USE the Manual Mode Select the manual modeMeasure your heart rate if desired HOW to USE a Preset Workout HOW to USE the Dumbbells Information ModeHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Compatible with GFCI-equipped outlets TroubleshootingProblem The power does not turn on Problem The power turns off during useTop Problem The walking belt slows when walked onProblem Solution Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Key No. Qty Description Part LIST-Model No. PMTL39708.0107 Filter Wire Userʼs Manual Exploded Drawing A-Model No. PMTL39708.0 R0509A Exploded Drawing B-Model No. PMTL39708.0 R0509A Exploded Drawing C-Model No. PMTL39708.0 Exploded Drawing D-Model No. PMTL39708.0 R0509A Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty