ProForm PFTL72707.0 user manual Assembly, Make sure that the power cord is unplugged

Page 6

ASSEMBLY

To hire an authorized service technician to assemble the treadmill, call 1-800-445-2480. Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-perfor- mance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included hex key and your own Phillips screwdriver (with a

shaft at least 6" long) and wire cutters .

Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of the manual. The number after the parentheses shows the quantity needed for assembly. Note: If a part is not in the parts bag, check to see if it is preat- tached to one of the parts to be assembled. Extra hardware may be included. To avoid damaging plastic parts, do not use power tools for assembly.

Extension Leg Nut (67)–4

Latch Shock

Star Washer (8)–4

Ground Screw

Screw (3)–9

 

(33)–1

 

 

Nut (30)–2

 

 

 

 

3/4" Screw (22)–4

Upper Latch Shock Bolt (50)–1

 

Lower Latch Shock Bolt (39)–1

Base Leg Bolt (65)–4

 

Handrail Bolt (64)–4

 

1. Make sure that the power cord is unplugged.

1

 

 

 

 

 

With the help of a second person, carefully tip

 

84

 

the treadmill onto its left side as shown.

65

 

 

Insert an Extension Leg (89) into the base of the

 

 

82

 

 

 

Uprights (84) as shown. Hold two Extension Leg

 

 

 

Nuts (67) in the bottom of the Extension Leg.

 

82

22

Next, insert two Base Leg Bolts (65) into the top

 

 

 

 

 

 

of the Extension Leg, and firmly tighten the

 

 

 

Base Leg Bolts into the Extension Leg Nuts.

 

22

 

 

89

 

Attach two Base Pads (82) to the base of the

67

 

 

 

 

Uprights (84) with two 3/4" Tek Screws (22).

 

 

 

 

6

 

 

Page 5 Page 7
Image 6
Page 5 Page 7
Contents QUESTIONS? Model No. PFTL72707.0 Serial NoCall TOLL-FREE Table of Contents Important Precautions Page Before YOU Begin Assembly Make sure that the power cord is unpluggedPage Be Damaged When the Power is Nected PROPERLY, the Console MAYMake sure that no wires are pinched Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeMeasure your heart rate if desired Turn on the fan if desiredHOW to USE a Cross Trainer Program Select one of the nine cross trainer programsPress the Start button to start the program Perform the first strength exercise when prompted Continue the cross trainer programSelect one of the custom programs HOW to Create a Custom ProgramSpeed and incline settings Press the Start button and program the desiredHOW to USE a Custom Program Information Mode Optional Chest Pulse SensorHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Top View Page Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencySuggested Stretches R0907A Key Qty DescriptionPage Drawinga Exploded Drawing B-Model No. PFTL72707.0 R0907A Exploded Drawing C-Model No. PFTL72707.0 R0907A Exploded Drawing D-Model No. PFTL72707.0 R0907A Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT
Top Page Image Contents