ProForm PFTL72707.0 user manual Make sure that no wires are pinched

Page 9

8.Set the console assembly on the Handrail (20).

Be careful to avoid pinching any of the wires. Make sure that the ground wire (see step 6) and the wire harness from the con- sole assembly (see step 7) are in the indi- cated channel.

Hand tighten five Screws (3) into the Handrail (20) and the console assembly. Start all five

Screws, but do not tighten them yet. Do not put Screws into the two indicated holes.

8

Console Assembly

 

 

 

Channel

 

 

 

20

 

3

3

3

 

 

No Screws

 

9.Hand tighten four additional Screws (3) into the Handrail (20) and the console assembly. Then, tighten all nine Screws used in step 8 and this step; do not overtighten the Screws.

9

Console Assembly

 

 

20

3

 

 

 

3

 

10.Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the tread- mill. Note: Extra hardware may be included. Keep the included hex key in a secure place; the hex key is used to adjust the walking belt (see pages 22 and 23).

If you purchase the optional chest pulse sensor (see page 18), follow the steps below to install the receiver included with the chest pulse sensor.

1. Remove the key from the console and unplug

85

 

the power cord.

 

 

 

Remove the Screw (3) and the Access Door

 

 

(76) from the back of the Console Base (85).

 

 

2. Connect the wire on the receiver (A) to the indi-

 

 

cated wire extending from the Console Base

 

 

(85). Hold the receiver so the small cylinder

 

 

is oriented as shown and is facing the

Small Screws

 

Console Base. Attach the receiver to the plastic

 

 

Wire

posts on the Access Door (76) with the two in-

A

 

cluded small screws.

 

 

 

3. Make sure that no wires are pinched.

Small

 

Cylinder

 

Reattach the Access Door (76) with the Screw

 

76

3

(3). Discard the other wires included with the re-

ceiver.

 

 

 

9

 

Image 9 Contents
QUESTIONS? Model No. PFTL72707.0 Serial NoCall TOLL-FREE Table of Contents Important Precautions Page Before YOU Begin Make sure that the power cord is unplugged AssemblyPage Nected PROPERLY, the Console MAY Be Damaged When the Power isMake sure that no wires are pinched Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerTurn on the fan if desired Measure your heart rate if desiredHOW to USE a Cross Trainer Program Select one of the nine cross trainer programsPress the Start button to start the program Continue the cross trainer program Perform the first strength exercise when promptedSpeed and incline settings HOW to Create a Custom ProgramSelect one of the custom programs Press the Start button and program the desiredHOW to USE a Custom Program Optional Chest Pulse Sensor Information ModeHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Top View Page Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Key Qty Description R0907APage Drawinga Exploded Drawing B-Model No. PFTL72707.0 R0907A Exploded Drawing C-Model No. PFTL72707.0 R0907A Exploded Drawing D-Model No. PFTL72707.0 R0907A Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT
Related manuals
Manual 32 pages 26.77 Kb