ProForm PFTL56007.0 user manual Top, Problem The walking belt slows when walked on

Page 26

Remove the three Hood Screws (7) from the Hood (41), and carefully pivot the Hood off.

7

7

41

Locate the Reed Switch (63) and the Magnet (46) on the left side of the Pulley (47). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If necessary, loosen the 1/2" Screw (33), move the Reed Switch slightly, and then retighten the Screw. Reattach the Hood (not shown); make sure that the Hood Screws (not shown) are inserted into the same holes from which they were removed. Run the treadmill for a few minutes to check for a correct speed reading.

Top

 

View

 

33

 

63

47

1/8 in.

46

PROBLEM: The incline of the treadmill does not change correctly

SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re- move the key. After a few seconds, reinsert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system.

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 11.

b. If the walking belt is overtightened, treadmill perfor- mance may decrease and the walking belt may be- come damaged. Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both rear roller bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 3 to 4 in. (8 to 10 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

b

3–4 in.

Rear Roller Bolts

c. If the walking belt still slows when walked on, please see the front cover of this manual.

26

Image 26
Contents Call TOLL-FREE QUESTIONS?Model No. PFTL56007.0 Serial No Table of Contents Important Precautions Page Before YOU Begin Assembly Make sure that the power cord is unpluggedBe careful not to pinch the Wire Harness Fully tighten the Upright Bolts yetConsole Bolts and then firmly tighten them Again. if the Connectors are not CONAvoid pinching the wires. While a second per Not to overtighten the Upright Bolts Top ViewWire PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the Console Select the manual mode HOW to Turn on the PowerHOW to USE the Manual Mode Insert the key into the consoleChange the incline of the treadmill as desired Follow your progress with the displayMeasure your heart rate if desired Turn on the fan if desiredPress the Start button to start the program HOW to USE a Cross Trainer ProgramSelect one of the six cross trainer programs Perform the first strength exercise when prompted Continue the cross trainer programHOW to USE the 5K Program Select the 5K programWhen you are finished exercising, remove HOW to USE a Weight Loss ProgramSelect a weight loss program See onHOW to USE the Performance Program Select the performance programInformation Mode Optional Chest Pulse SensorHOW to USE the Upper Body Arms HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on TopPage Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencySuggested Stretches R0108A Qty DescriptionDescription Drawing a Exploded Drawing B-Model No. PFTL56007.0 Exploded Drawing C-Model No. PFTL56007.0 Exploded Drawing D-Model No. PFTL56007.0 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty