ProForm PFTL56007.0 user manual

Page 27

PROBLEM: The walking belt is off-center or slips when walked on

SOLUTION: a. If the walking belt is off-center, first remove the key and UNPLUG THE POWER CORD. If the walking belt has shifted to the left, use the hex key to turn the left rear roller bolt clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the left bolt counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is centered.

b. If the walking belt slips when walked on, first re- move the key and UNPLUG THE POWER CORD. Using the hex key, turn both rear roller bolts clock- wise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each edge of the walking belt 3 to 4 in. (8 to 10 cm) off the walking plat- form. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and care- fully walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

PROBLEM: The upper body arms squeak during use

a

b

SOLUTION: a. (Note: Correcting this problem requires a small amount of white marine grease, available at hardware stores.) Turn the Resistance Knob (A) counterclock- wise and remove it. Next, remove the Resistance Cone (B) and the Upper Body Arm (109), along with the Resistance Plate (C), Washers (D), Spring Washer (E), Thrust Washers (F), and Thrust Bearing (G). (Note: If the Resistance Plate [C] comes out of the Resistance Cone [B], press it back in.) Apply a thin layer of white marine grease to the outer surface of the Resistance Cone (B). Then, reattach all parts in the order shown at the right.

109

B

F

E

C

G

D

A

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents QUESTIONS? Model No. PFTL56007.0 Serial NoCall TOLL-FREE Table of Contents Important Precautions Page Before YOU Begin Make sure that the power cord is unplugged AssemblyFully tighten the Upright Bolts yet Be careful not to pinch the Wire HarnessAgain. if the Connectors are not CON Avoid pinching the wires. While a second perConsole Bolts and then firmly tighten them Top View Not to overtighten the Upright BoltsWire Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the Console Insert the key into the console HOW to Turn on the PowerHOW to USE the Manual Mode Select the manual modeFollow your progress with the display Change the incline of the treadmill as desiredTurn on the fan if desired Measure your heart rate if desiredHOW to USE a Cross Trainer Program Select one of the six cross trainer programsPress the Start button to start the program Continue the cross trainer program Perform the first strength exercise when promptedSelect the 5K program HOW to USE the 5K ProgramSee on HOW to USE a Weight Loss ProgramSelect a weight loss program When you are finished exercising, removeSelect the performance program HOW to USE the Performance ProgramOptional Chest Pulse Sensor Information ModeHOW to USE the Upper Body Arms HOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingTop Problem The walking belt slows when walked onPage Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Qty Description R0108ADescription Drawing a Exploded Drawing B-Model No. PFTL56007.0 Exploded Drawing C-Model No. PFTL56007.0 Exploded Drawing D-Model No. PFTL56007.0 Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT
Top Page Image Contents