ProForm PFTL54706.0 user manual Console Wire Bracket Tie Large Hole

Page 9

7.Set the Console Assembly (91) face down on a soft surface to avoid scratching the Console Assembly. Hold the Right Handrail (33), which has a large hole in one side, near the Console.

Next, insert the console wire and the tie into the hole in the side of the Right Handrail (33). Using needlenose pliers, pull the console wire out of the hole near the bracket on the Right Handrail.

Then, set the Right Handrail (33) on the Console Assembly (91). Make sure that no wires are pinched. Start a Crossbar Screw (85) with a Crossbar Star Washer (7) into the Right Handrail, and then start two Console Screws (10) into the Right Handrail. Tighten the

Crossbar Screw and then tighten the two Console Screws; do not overtighten the Screws.

Attach the Left Handrail (not shown) to the Console Assembly (91) in the same way. Note: There are no wires on the left side.

8.See drawing 8a. If there is a guard on the end of the Console Wire, press the indicated tab and re- move the guard with needlenose pliers. Discard the guard.

With the help of a second person, hold the Console Assembly (91) near the Right Upright (54).

Remove the wire tie from the Wire Harness (39). Connect the Wire Harness to the console wire harness. Make sure to connect the connec- tors properly (see drawing 8b). The connec- tors should slide together easily and snap into place. If they do not, turn one connector and try again. IF THE CONNECTORS ARE NOT

CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. Insert the connectors and the ex- cess wire downward into the Right Upright (54).

7

Console

 

 

 

 

 

 

Wire

85

 

 

 

 

Bracket

Tie

7

 

 

10

 

 

 

33

Large

 

 

Hole

 

 

 

 

 

 

91

 

 

8

 

 

8a

Console

Wire

Tab 91

Guard

39

Console Wire

8b

Harness

 

 

 

54

39

 

9.Attach the Console Assembly (91) to the Right Upright (54) and the Left Upright (53) with four four Handrail Bolts (8) and four Handrail Star Washers (5). Make sure that no wires are pinched. Start all four Handrail Bolts but do not tighten them yet.

9

91

 

 

 

 

8

8

 

5

5

 

54

53

9

 

 

Image 9
Contents QUESTIONS? Model No. PFTL54706.0 Serial NoCall TOLL-FREE Table of Contents Important Precautions Page Before YOU Begin Make sure that the power cord is unplugged AssemblyPage Washer 9 do not tighten the Colored Patch Frame Bolt yet Outer side of the Frame Spacer facingConsole Wire Bracket Tie Large Hole Overtighten the Belly Pan Screws Top View Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerTurn on the fan if desired Measure your heart rate if desiredHOW to USE a Cross Training Program Select one of the six cross training programsPress the Start button to start the program Continue the cross training program Perform the first strength exercise when PromptedSelect a preset program HOW to USE a Preset ProgramFollow your progress with the display Optional Chest Pulse Sensor Information ModeHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use Maintenance and TroubleshootingProblem The walking belt slows when walked on Exercise Intensity Conditioning GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Key Qty Description R1006AExploded Drawing A-Model No. PFTL54706 Exploded Drawing B-Model No. PFTL54706.0 R1006A Exploded Drawing C-Model No. PFTL54706.0 R1006A Exploded Drawing D-Model No. PFTL54706.0 R1006A Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT