Operating JVC’s Audio/Video Components
You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC’s components are preset in the remote control.
English
Operating Audio Components
IMPORTANT:
To operate JVC’s audio components using the supplied remote control:
•You need to connect JVC’s audio components through the COMPU LINK (SYNCHRO) jacks (see page 30) in addition to the connections using cables with RCA pin plugs (see page 7).
•Aim the remote control directly at the remote sensor on the receiver.
•If you use the buttons on the front panel to choose a source, the remote control will not operate that source. To operate a source with the remote control, the source must be selected using source selection buttons on the remote control.
•To operate the target component using the COMPU LINK remote control system, set the source name correctly if required. (See page 14.)
•Refer also to the manuals supplied with your components.
Sound control section (Amplifier)
You can always perform the following operations:
STANDBY/ON 
AUDIO:
Turn on or off the receiver.
VOLUME
MUTING: Turn on or off sound muting.
ANALOG/DIGITAL: Switch the analog and digital input alternately.
DIMMER: Dim or brighten the display.
SLEEP:Set the Sleep Timer.
SURROUND: Turn on and select Surround modes.
DSP:Turn on and select DSP modes.
SURROUND/DSP OFF:
Turn off the Surround and DSP mode.
BASSBOOST: Only for
After pressing SOUND, you can perform the following operations by using the 10 keys:
FRONT L then LEVEL
level.
FRONT R then LEVEL
| level. |
CENTER then LEVEL | Adjust the center speaker output level. |
SURR L then LEVEL | Adjust the left surround speaker |
| output level. |
SURR R then LEVEL | Adjust the right surround speaker |
| output level. |
SUBWFR then LEVEL
EFFECT: | Adjust the effect level. |
TEST: | Turn on or off test tone output. |
Note:
After adjusting sounds, press the corresponding source selection button to operate your target source by using the 10 keys; otherwise, the 10 keys cannot be used for operating your target source.
Tuner
You can always perform the following operations:
FM/AM: Alternate between FM and AM.
After pressing FM/AM, you can perform the following operations on a tuner:
1 – 10, +10: Select a preset channel number directly. For channel number 5, press 5.
For channel number 15, press +10, then 5. For channel number 20, press +10, then 10.
FM MODE: Change the FM reception mode.
CD player
After pressing CD, you can perform the following operations on a CD player:
3: | Start playing. |
4: | Return to the beginning of the current (or previous) |
| track. |
¢: | Skip to the beginning of the next track. |
7: | Stop playing. |
8: | Pause playing. To resume, press 3. |
1 – 10, +10: Select a track number directly. For track number 5, press 5.
For track number 15, press +10, then 5. For track number 20, press +10, then 10.
For track number 30, press +10, +10, then 10.
CD changer
After pressing
3: | Start playing. |
4: | Return to the beginning of the current (or previous) |
| track. |
¢: | Skip to the beginning of the next track. |
7: | Stop playing. |
8: | Pause playing. To resume, press 3. |
1 – 6, 7/P: | Select the number of a disc installed in a CD |
| changer. |
After pressing CD, you can perform the following operations on a CD changer:
1 – 10, +10: Select a track number directly. For track number 5, press 5.
For track number 15, press +10, then 5. For track number 20, press +10, then 10.
For track number 30, press +10, +10, then 10.
Example:
•Selecting disc number 4, track number 12, and starting playback.
1 Press CD-DISC, then press 4.
2 Press CD, then press +10, 2.
Continued on the next page
33