JVC RX-D402B Operating procedure, Press Setting, Button, Ex. When setting Digital in 1 terminal

Page 24
Initial setting:
Select when you have disconnected a speaker. (Not selectable for the front speakers.)
<LRG> (for the front speakers) <SML> (for other speakers)
<NO>
Select when the cone speaker size is smaller than 12 cm (4 3/4 inches).
<SML> (small)
Select when the cone speaker size is larger than 12 cm (4 3/4 inches).
<LRG> (large)
Setting the speaker size—FRONT SPK (front speakers), CENTER SPK (center speaker), SURROUND SPK (surround speakers), S BACK SPK (surround back speakers)
Register the sizes of all the connected speakers.
Initial setting:
SUBWFR <NO>
Select when you have disconnected a subwoofer. Selecting this changes the front speaker size to “LRG” (see below).
SUBWFR <NO>
Select when you have connected a subwoofer.
The subwoofer indicator ( S.WFR ) lights up on the display. You can adjust the subwoofer output level (see page 28).
SUBWFR <YES>
• On the front panel, press SETTING.
The source indication resumes on the display.
Setting the speakers
To obtain the best possible surround effect from the Surround and DSP modes, register the setting about the speaker after all connections are completed.
• If you have used Quick Speaker Setup on page 20, this setting is not required.
Setting subwoofer information—SUBWOOFER
Select whether you have connected a subwoofer or not.
Press EXIT.
7
Your setting is stored.
5 Press SET.
6 Repeat steps 2 to 5 to set other items if necessary.
DBS
VCR
DVR/DVD
TV
4 Press 2 / 3 button repeatedly to select the appropriate setting.
• On the front panel, turn MULTI JOG.
ANALOG
L R S.WFR

Operating procedure

Menu operation buttons

On the front panel:

 

1,7

3,5

2,4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

From the remote control:

1

2

(5 / ∞ button)

3,5 (SET button)

 

4

(2 / 3 button)

7

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

In this section, the operation of the remote control is used for explaining.

Ex.: When setting DIGITAL IN 1 terminal.

1Press SETTING.

MULTI JOG now works for the setting operation.

2Press 5 / ∞ button repeatedly until the item you want to set appears on the display.

•On the front panel, turn MULTI JOG.

•As you press 5 / ∞ button, the setting items change as

follows:

ANALOG

LR

S.WFR

QUICK SPK SET FRONT SPK SURROUND SPK S BACK OUT FRONT L DIST CENTER DIST SURR R DIST S BACK L DIST EX/ES/PLIIx

SUBWOOFER OUT LFE ATT DIGITAL IN 1 DIGITAL IN 3 ONE TOUCH OP CMPNT SELECT

(Back to the beginning)

SUBWOOFER CENTER SPK S BACK SPK DIST UNIT FRONT R DIST SURR L DIST S BACK DIST S BACK R DIST DUAL MONO CROSSOVER MIDNIGHT MODE DIGITAL IN 2 AUDIO DELAY HDMI SELECT VIDEO OUTPUT

3Press SET.

The current setting of the selected item appears.

ANALOG

LR

S.WFR

22

Page 23 Page 25
Image 24
Page 23 Page 25
Contents RX-D401S / RX-D402B For Customer UseFor Canada/pour le Canada For U.S.AFor U.S.A JVCFeatures Table of Contents Remote control When operating a DVD player, set the mode selector o to DVDParts identification AUDIO, TV , DBS/CATV , VCR , DVR/DVDDisplay window Front panelRear panel VCR DBS IN, DVR/DVD IN, Monitor OUTCENTER, SUBWOOFER, Surr L, Surr R Surround Back SPEAKERS, Surround SpeakersBefore Installation Putting batteries in the remote controlChecking the supplied accessories Getting startedConnecting the FM and AM antennas FM antenna connectionFM antenna supplied AntennaConnecting the speakers Speaker Layout DiagramConnecting the speakers Connecting the powered subwooferConnecting video components Converting video signals into Hdmi signalsHdmi connection Turn off all components before making connectionsAudio/video connection Only for DVD recorder To left/right audio channel inputDVD recorder or Monaural audio cable Not suppliedWhite Only for DVD recorder To S-video inputRed Stereo audio cable Not supplied Connecting a DBS tuner Connecting a TVConnecting the power cord Digital audio connectionDigital input terminals Digital output terminalUSB connection Turn on the power To turn off the power into standbySelecting the video input setting Basic operationsAdjust the volume Selecting the audio input settingListening with headphones Hdmi for DVR/DVD, VCR and DBSSelecting the digital decode mode To restore the sound, press Muting againTurning off the sounds temporarily Changing the display brightnessTurning off the power with the Sleep Timer Basic adjustment of auto memorySignal and speaker indicators on the display From the remote control only Press Sleep repeatedlyBasic settings On the front panel From the remote controlMenu operation buttons Press SETBasic setting items Speakers channels number and the sizeRoom size and the speaker distance/output level Operating procedure Press SettingEx. When setting Digital in 1 terminal ButtonSetting the speaker distance Initial setting SB OUT 2SPKInitial setting Unit meter Speaker distance OUTActivating the EX/ES/PLIIx setting- EX/ES/PLIIx Setting bass soundSetting subwoofer output-SUBWOOFER OUT Selecting the main or sub channelUsing the Midnight mode Setting the low frequency effect attenuator-LFESetting the Audio delay level Memorizing the volume level for each source-ONE Touch OPSelecting the output video signals Sound adjustments Basic adjustment itemsPress Adjust ∞ button SET button 4 2 / 3 buttonSBR SBL Press Test to check the speakers’ output balanceAdjusting the bass sounds Adjusting the virtual room size for DSP modesAttenuating the input signal-INPUT ATT Adjusting the liveness effect for DSP modesAdjusting the center tone-CENTER Tone Tuning in to stations manually Using preset tuningTo store the preset stations Tuner operationsSelecting the FM reception mode To tune in a preset stationCreating realistic sound fields Reproducing theater ambienceIntroducing the Surround modes Dolby DigitalAbout other digital signals DTSAll Channel Stereo mode ALL CH Stereo 3D Headphone modeIntroducing the DSP modes Digital Acoustic Processor DAP modesUsing the Surround/DSP modes DTSDolby Digital Incoming Signal TypeAbout the DSP modes Virtual Surround BackWhen you select Auto Surround Selecting the Surround/DSP modesAV Compu Link remote control system Connections 1 AV Compu Link connectionConnections 2 Video cable connection Monaural mini-plugs not suppliedConnecting procedure Automatic selection of TV’s input modeAutomatic power on/off One-touch DVD playOperating other JVC products VCRChannel + REWChanging the remote control code for DVD recorder DVD recorder or DVD playerRelease DVR/DVD DVD MenuChanging the transmittable signals for operating a TV Operating other manufacturers’ productsRelease TV Try to operate your TV by pressing TVChanging the transmittable signals for operating a VCR Release VCRTry to operate your VCR by pressing VCR Manufacturers’ codes for VCRRelease DBS/CATV Manufacturers’ codes for Catv converterManufacturers’ codes for DBS tuner Try to operate your DVD player by pressing DVR/DVDTroubleshooting PowerProblem Possible Cause Solution Sound and pictureRemote control Tuner Specifications AmplifierFM tuner IHF AM tunerPage Page 0705RYMMDWJEIN

RX-D401S, RX-D402B specifications

The JVC RX-D402B and RX-D401S are two impressive models from JVC's lineup of AV receivers, designed to elevate the audio-visual experience for home theater enthusiasts. Both units incorporate cutting-edge technologies and features aimed at delivering superior sound quality and versatility.

The RX-D402B is a robust receiver that emphasizes high-definition audio performance. It supports various audio formats, including Dolby TrueHD and DTS-HD Master Audio, ensuring an immersive surround sound experience. One of its standout features is its 4K video processing capability, allowing users to connect their latest high-resolution devices seamlessly. With multiple HDMI inputs, it can accommodate various sources, from gaming consoles to streaming devices.

Similarly, the RX-D401S provides a compelling feature set designed for audiophiles. This model supports a wide array of streaming services, making it easy to access music libraries and online content. Bluetooth connectivity is another significant advantage, allowing users to stream audio directly from smartphones and tablets without hassle. An integrated digital tuner and built-in Wi-Fi make this receiver a versatile option for entertainment.

Both models employ JVC's proprietary audio technology, designed to enhance sound clarity and fidelity. Equipped with high-quality DACs (Digital-to-Analog Converters), they ensure that audio playback remains crisp and dynamic, regardless of the source. Users can also take advantage of the advanced equalization settings, enabling them to tailor the sound profile to their liking.

Another notable aspect of these receivers is their user-friendly interface. The on-screen display simplifies navigation through various settings and options. Additionally, these models come with comprehensive remote controls that allow users to manage their entire audio-visual systems effortlessly.

In terms of build quality, both the RX-D402B and RX-D401S feature durable construction and a sleek design, making them appealing additions to any home theater setup. They are also equipped with multiple outputs, including subwoofer outputs, ensuring compatibility with a range of speaker configurations.

With support for high-definition audio formats, seamless streaming options, and robust performance features, the JVC RX-D402B and RX-D401S are excellent choices for those looking to enhance their home entertainment experience. Whether enjoying a movie night, gaming session, or listening to music, these receivers offer a high-quality audio experience that meets the demands of modern consumers.
Top Page Image Contents