JVC RX-D402B manual Getting started, Before Installation, Putting batteries in the remote control

Page 8

Getting started

Before Installation

General precautions

•Be sure your hands are dry.

•Turn the power off to all components.

•Read the manuals supplied with the components you are going to connect.

Locations

•Install the receiver in a location that is level and protected from moisture and dust.

•The temperature around the receiver must be between –5˚C and 35˚C (23˚F and 95˚F).

•Make sure there is good ventilation around the receiver. Poor ventilation could cause overheating and damage the receiver.

•Leave sufficient distance between the receiver and the TV.

Handling the receiver

•Do not insert any metal object into the receiver.

•Do not disassemble the receiver or remove screws, covers, or cabinet.

•Do not expose the receiver to rain or moisture.

•Do not pull on the power cord to unplug the cord. When unplugging the cord, always grasp the plug so as not to damage the cord.

•When you are away on travel or otherwise for an extended period or time, remove the plug from the wall outlet. A small amount of power is always consumed while the power cord is connected to the wall outlet.

The receiver has a built-in cooling fan which operates while the receiver is turned on. Be sure to leave enough ventilation to obtain sufficient cooling effect.

CAUTION:

Do not connect the AC power plug to the wall outlet until all

connections are completed.

Putting batteries in the remote control

Before using the remote control, put two supplied batteries first.

1

2

3

1Press and slide the battery cover on the back of the remote control.

2Insert batteries.

Make sure to match the polarity: (+) to (+) and (–) to (–).

3Replace the cover.

If the range or effectiveness of the remote control decreases, replace the batteries. Use two R6(SUM-3)/AA(15F) type dry-cell batteries.

•Supplied butteries are for initial setup. Replace for continued use.

CAUTION:

Follow these precautions to avoid leaking or cracking cells:

•Place batteries in the remote control so they match the polarity:

(+) to (+) and (–) to (–).

•Use the correct type of batteries. Batteries that look similar may differ in voltage.

•Always replace both batteries at the same time.

•Do not expose batteries to heat or flame.

When using the remote control, aim the remote control directly at the remote sensor on the front panel.

Remote sensor

Checking the supplied accessories

Check to be sure you have all of the following supplied accessories. If anything is missing, contact your dealer immediately.

•Remote control (⋅ 1)

•Batteries (⋅ 2)

•AM loop antenna (⋅ 1)

•FM antenna (⋅ 1)

6

Page 7 Page 9
Image 8
Page 7 Page 9
Contents RX-D401S / RX-D402B For Customer UseFor Canada/pour le Canada For U.S.AFor U.S.A JVCFeatures Table of Contents Remote control When operating a DVD player, set the mode selector o to DVDParts identification AUDIO, TV , DBS/CATV , VCR , DVR/DVDDisplay window Front panelRear panel VCR DBS IN, DVR/DVD IN, Monitor OUTCENTER, SUBWOOFER, Surr L, Surr R Surround Back SPEAKERS, Surround SpeakersBefore Installation Putting batteries in the remote controlChecking the supplied accessories Getting startedConnecting the FM and AM antennas FM antenna connectionFM antenna supplied AntennaConnecting the speakers Speaker Layout DiagramConnecting the speakers Connecting the powered subwooferConnecting video components Converting video signals into Hdmi signalsHdmi connection Turn off all components before making connectionsAudio/video connection Only for DVD recorder To left/right audio channel inputDVD recorder or Monaural audio cable Not suppliedWhite Only for DVD recorder To S-video inputRed Stereo audio cable Not supplied Connecting a DBS tuner Connecting a TVConnecting the power cord Digital audio connectionDigital input terminals Digital output terminalUSB connection Turn on the power To turn off the power into standbySelecting the video input setting Basic operationsAdjust the volume Selecting the audio input settingListening with headphones Hdmi for DVR/DVD, VCR and DBSSelecting the digital decode mode To restore the sound, press Muting againTurning off the sounds temporarily Changing the display brightnessTurning off the power with the Sleep Timer Basic adjustment of auto memorySignal and speaker indicators on the display From the remote control only Press Sleep repeatedlyBasic settings On the front panel From the remote controlMenu operation buttons Press SETRoom size and the speaker distance/output level Basic setting itemsSpeakers channels number and the size Operating procedure Press SettingEx. When setting Digital in 1 terminal ButtonSetting the speaker distance Initial setting SB OUT 2SPKInitial setting Unit meter Speaker distance OUTActivating the EX/ES/PLIIx setting- EX/ES/PLIIx Setting bass soundSetting subwoofer output-SUBWOOFER OUT Selecting the main or sub channelUsing the Midnight mode Setting the low frequency effect attenuator-LFESelecting the output video signals Setting the Audio delay levelMemorizing the volume level for each source-ONE Touch OP Sound adjustments Basic adjustment itemsPress Adjust ∞ button SET button 4 2 / 3 buttonSBR SBL Press Test to check the speakers’ output balanceAdjusting the bass sounds Adjusting the virtual room size for DSP modesAttenuating the input signal-INPUT ATT Adjusting the liveness effect for DSP modesAdjusting the center tone-CENTER Tone Tuning in to stations manually Using preset tuningTo store the preset stations Tuner operationsSelecting the FM reception mode To tune in a preset stationCreating realistic sound fields Reproducing theater ambienceIntroducing the Surround modes Dolby DigitalAbout other digital signals DTSAll Channel Stereo mode ALL CH Stereo 3D Headphone modeIntroducing the DSP modes Digital Acoustic Processor DAP modesUsing the Surround/DSP modes DTSDolby Digital Incoming Signal TypeAbout the DSP modes Virtual Surround BackWhen you select Auto Surround Selecting the Surround/DSP modesAV Compu Link remote control system Connections 1 AV Compu Link connectionConnections 2 Video cable connection Monaural mini-plugs not suppliedConnecting procedure Automatic selection of TV’s input modeAutomatic power on/off One-touch DVD playOperating other JVC products VCRChannel + REWChanging the remote control code for DVD recorder DVD recorder or DVD playerRelease DVR/DVD DVD MenuChanging the transmittable signals for operating a TV Operating other manufacturers’ productsRelease TV Try to operate your TV by pressing TVChanging the transmittable signals for operating a VCR Release VCRTry to operate your VCR by pressing VCR Manufacturers’ codes for VCRRelease DBS/CATV Manufacturers’ codes for Catv converterManufacturers’ codes for DBS tuner Try to operate your DVD player by pressing DVR/DVDTroubleshooting PowerProblem Possible Cause Solution Sound and pictureRemote control Tuner Specifications AmplifierFM tuner IHF AM tunerPage Page 0705RYMMDWJEIN

RX-D401S, RX-D402B specifications

The JVC RX-D402B and RX-D401S are two impressive models from JVC's lineup of AV receivers, designed to elevate the audio-visual experience for home theater enthusiasts. Both units incorporate cutting-edge technologies and features aimed at delivering superior sound quality and versatility.

The RX-D402B is a robust receiver that emphasizes high-definition audio performance. It supports various audio formats, including Dolby TrueHD and DTS-HD Master Audio, ensuring an immersive surround sound experience. One of its standout features is its 4K video processing capability, allowing users to connect their latest high-resolution devices seamlessly. With multiple HDMI inputs, it can accommodate various sources, from gaming consoles to streaming devices.

Similarly, the RX-D401S provides a compelling feature set designed for audiophiles. This model supports a wide array of streaming services, making it easy to access music libraries and online content. Bluetooth connectivity is another significant advantage, allowing users to stream audio directly from smartphones and tablets without hassle. An integrated digital tuner and built-in Wi-Fi make this receiver a versatile option for entertainment.

Both models employ JVC's proprietary audio technology, designed to enhance sound clarity and fidelity. Equipped with high-quality DACs (Digital-to-Analog Converters), they ensure that audio playback remains crisp and dynamic, regardless of the source. Users can also take advantage of the advanced equalization settings, enabling them to tailor the sound profile to their liking.

Another notable aspect of these receivers is their user-friendly interface. The on-screen display simplifies navigation through various settings and options. Additionally, these models come with comprehensive remote controls that allow users to manage their entire audio-visual systems effortlessly.

In terms of build quality, both the RX-D402B and RX-D401S feature durable construction and a sleek design, making them appealing additions to any home theater setup. They are also equipped with multiple outputs, including subwoofer outputs, ensuring compatibility with a range of speaker configurations.

With support for high-definition audio formats, seamless streaming options, and robust performance features, the JVC RX-D402B and RX-D401S are excellent choices for those looking to enhance their home entertainment experience. Whether enjoying a movie night, gaming session, or listening to music, these receivers offer a high-quality audio experience that meets the demands of modern consumers.
Top Page Image Contents