JVC SP-D302 Presetting Stations, Changing the FM Reception Mode, Three Ways to Select a Station

Page 13

1

FM/AM

or

2

3 1 2 3

CLOCK TIMER

4 5 6

– SELECT +

7 8 9

SET

10 10

Three Ways to Select a Station ——————————————

oPress the TUNING DOWN or TUNING UP on the MULTI CONTROL repeatedly to move from frequency to frequency until you find the one you want. (Manual Tuning).

OR

oPress and hold the TUNING DOWN or TUNING UP on the MULTI CONTROL for a few seconds, the frequency starts changing on the display. When a station is tuned in, the frequency stops changing.

(Auto Tuning).

OR

oPossible only after presetting stations.

Press once and release the P. DOWN or P. UP on the MULTI CONTROL to go to the next preset station.

You can also use the Remote Control to tune in preset channels:

1.Press the FM/AM button so that you can receive the most recent station tuned in.

2.Select the station by entering the preset number in the number keys of the Remote Control.

Example: for channel 5, press 5. For channel 15, press +10 then 5. For channel 20, press +10, then 10. For channel 30, press +10 twice then 10.

After you have selected the preset number and the number is displayed, the broadcast frequency of the selected channel is displayed.

Presetting Stations

You can preset up to 30 FM stations and up to 15 AM stations for the preset numbers.

Note: In some cases, test frequencies have been already memorized for the tuner since the factory examined the tuner preset function before shipment. This is not a malfunction. You can preset the stations you want into memory by following the presetting method.

1.Select a band by pressing the FM/AM button.

2.Press the TUNING DOWN or TUNING UP on the MULTI CONTROL to tune into a station.

3.Press and hold the number keys on the Remote Control for a few seconds to set the preset number.

For preset numbers 1 to 10:

Press the number key for the preset number you want to set.

For preset numbers 11 to 20:

Press the 1 to 10 buttons after pressing the +10 button.

For preset numbers 21 to 30:

Press the 1 to 10 buttons after pressing the +10 button twice.

The preset number appears in the display after you have pressed the number keys. If you press and hold the button, the preset number display blinks. Release the button after the number starts to blink. This completes the preset setting.

4.Repeat steps 1 to 3 for each station you want to store in memory with a preset number.

CAUTION: If the Unit is unplugged or if a power failure occurs, the preset stations will be erased in a few days. If this happens, preset the station again.

FM MODE

Changing the FM Reception Mode

When an FM stereo broadcast is hard to receive or noisy, press the FM MODE button on the Remote Control so that the MONO indicator lights up in the display. Reception improves, but there is no stereo effect.

To restore the stereo effect, press the FM MODE button on the Remote Control so that the MONO indicator goes off. In this stereo mode, the ST indicator lights up and you can hear stereo effects, when a program is broadcast in stereo.

11

Image 13
Contents MX-D302T Important for Laser Products Installation of the Unit FeaturesPower cord How This Manual Is OrganizedTable of Contents How to Put Batteries in the Remote Control AccessoriesUsing the Remote Control Getting StartedConnecting the AM Antenna Connecting the FM AntennaUsing the Supplied Wire Antenna Using an FM 75-Ohm Antenna Cable not suppliedConnecting Auxiliary Equipment Connecting the SpeakersVCR or other equipment Right SpeakerOn the Unit On the Remote ControlCommon Operations Turning the Power On and OffDisplay Turning the System OnReinforcing the Bass Sound Adjusting the VolumeSound Modes Listening to Auxiliary Equipment Set the Volume control to Press the AUX buttonTuning In a Station Using the TunerSwitching between Frequency Bands One Touch RadioChanging the FM Reception Mode Presetting StationsThree Ways to Select a Station Disc indicators Using the CD PlayerCD £/8 Loading Discs For Normal Play Play mode indicator is not litQuickest Way to Start a CD Is with the One Touch Operation Place a CD, with its label side up, onto the trayLocating a Track With the Remote Control Directly Basics of Using the CD Player Normal PlayPlaying a Disc Selecting a Disc, Track Or Passage Within a TrackProgramming the Playing Order of the Tracks Continuous PlayPress the Random button Random PlayPress the £/8 button Tray Lock Function Repeating a Selection or the DiscsLocking the Trays Unlocking the TraysRegular Play Using the Cassette DeckOne Touch Play Press the 0 button for the deck you want to useMusic Scan Reverse ModeFast Left And Fast Right Finding the Beginning of the Current SelectionThings to Know before You Start Recording RecordingStandard Recording CD Direct Recording How to Use the Dubbing ButtonTape to Tape Recording Dubbing Recording AM Station to TapeSetting the Clock Using the TimerPress the Shift button Press the 1 Clock button Press the Select 5 + or 4 button to set the timeSet the time you want the Unit to come on Setting the TimerSet the time you want the Unit to turn off Press the Select 5 + or 4 button to select the sourceTo Change the Sleep Timer Setting Setting the Sleep TimerTo Cancel the Sleep Timer Setting Before Turning the Unit OffCare And Maintenance Symptom TroubleshootingPossible Cause ActionDon’t service it yourself HOW to Locate Your JVC Service CenterLimited Warranty AUDIO-1 Specifications